3 Phase Wattage Calculator
Enter voltage, current, and power factor to find the real power draw of any three-phase load in watts and kilowatts.
Use line-to-line volts, the reading between any two phases.
The line current in amps, per phase.
Motors typically run 0.7–0.9; use 1 for pure heating loads.
Pick how your voltage reading was taken.
Real power draw
—
Kilowatts (kW)
—
Apparent power (kVA)
—
Power at PF = 1 (amps check)
—
Current used in calculation
—
Line-to-line vs line-to-neutral: most nameplates and clamp meters quote line-to-line voltage, which uses the √3 formula. If you measured phase-to-neutral (common on 230 V lighting circuits), switch the dropdown so the calculator uses 3 × V instead.
Three-phase power runs the industrial world. Motors, pumps, compressors, welders, and large HVAC systems almost all draw three-phase electricity, and sizing any of them starts with one calculation: how many watts does the load actually draw?
The 3 phase wattage calculator turns three simple measurements, voltage, current, and power factor, into real power in watts and kilowatts. It also shows apparent power in kVA and a handy amps check that tells you the maximum power the same current could deliver.
This guide explains the formula, the difference between line-to-line and line-to-neutral voltage, what power factor really does, and walks through four worked examples with real numbers. Fifteen frequently asked questions follow at the end.
What the 3 Phase Wattage Calculator Tells You
The calculator takes four inputs: voltage in volts, current in amps, power factor as a number between 0 and 1, and how the voltage was measured, line-to-line or line-to-neutral. From these it computes the real power your load draws.
The headline result is real power in watts, the number that actually does work and that you pay for. It also shows kilowatts, apparent power in kVA, and the maximum possible power at a power factor of 1, which serves as an amps check on your numbers.
Everything updates from one press of the Calculate button. If any input is missing or out of range, the calculator explains what to fix instead of guessing.
How Three-Phase Power Works
In a three-phase system, three alternating currents flow through three wires, each one peaking at a different time. The peaks are spaced 120 degrees apart, so power delivery stays smooth instead of pulsing like single-phase power.
This smoothness is why motors prefer three phases. A single-phase motor needs help starting and vibrates more, while a three-phase motor starts itself and runs evenly. The same smooth delivery also means less copper is needed for the same power.
For the calculator, the practical point is simple: three-phase power is not three times single-phase power by accident. The geometry of the three waveforms introduces the square root of 3 into the formula, and the calculator handles that for you.
How to Use the 3 Phase Wattage Calculator
Enter the voltage first. Use the line-to-line reading, which is the voltage between any two of the three phases, for example 400 volts. This is the number most nameplates and clamp meters report.
Next enter the current in amps. This is the line current, the amps flowing in each phase conductor. Then enter the power factor, a number between 0 and 1. If you do not know it, 0.85 is a reasonable guess for a motor under load, and 1.0 is correct for heaters.
Finally, choose how the voltage was measured. Leave the default line-to-line setting unless you measured from a phase to neutral, which is common on 230 volt lighting circuits. Press Calculate to see the results.
The Real Power Formula
Real power is the power that does useful work, and it is what the calculator reports in watts. The formula depends on how the voltage was measured.
The formula is:
P = √3 × V × I × PF (line-to-line voltage)
P = 3 × V × I × PF (line-to-neutral voltage)
Here V is volts, I is amps, and PF is the power factor. Dividing the watt result by 1,000 gives kilowatts. Leaving PF out of the formula gives apparent power in volt-amps instead of watts.
Line-to-Line vs Line-to-Neutral Voltage
This choice trips up more people than any other part of three-phase math. Line-to-line voltage is measured between two phase wires, like 400 volts in a European industrial supply. Line-to-neutral voltage is measured between one phase and neutral, like 230 volts on the same system.
The two readings are related: line-to-line voltage equals line-to-neutral voltage times the square root of 3. That is exactly why the two formulas look different but give the same answer when fed matching measurements.
The calculator asks which one you measured so it can pick the right formula. If you enter a 230 volt line-to-neutral reading but leave the line-to-line setting on, the result will be wrong by a factor of about 1.73, so this dropdown matters.
What Power Factor Really Means
Power factor measures how much of the current actually does work. A motor stores energy in its magnetic field and returns part of it to the supply each cycle. That borrowed-and-returned energy draws current without doing work, so the power factor drops below 1.
A power factor of 0.85 means 85% of the apparent power becomes real, useful watts. The other 15% sloshes back and forth. Resistive heaters do not store energy this way, so their power factor is 1 and every amp does work.
Utilities care about power factor because the wasted current still heats their wires. Large customers with low power factor often pay penalties, which is why factories install capacitor banks to correct it.
Watts, Kilowatts, and kVA: What Is the Difference
Watts measure real power, the part that turns the motor shaft or heats the element. Kilowatts are simply watts divided by 1,000, and your electricity bill is based on kilowatt-hours of this real power.
kVA measures apparent power, the combination of real power and the borrowed-and-returned reactive power. It is always equal to or larger than the kilowatt figure, and the power factor is exactly the ratio between them: kW ÷ kVA = PF.
Generators and transformers are rated in kVA because they must carry the total current, useful or not. Motors are rated in kW or horsepower because that is the useful output. The calculator shows both so you can size either one.
Why the Square Root of 3 Appears in the Formula
The square root of 3, about 1.732, comes from the geometry of three-phase waveforms. When you measure line-to-line voltage, you are reading across two phases whose waveforms peak at different times, and the vector sum of the two gives the √3 factor.
You do not need to derive it to use the calculator, but knowing it exists protects you from a common error. Multiplying volts times amps times 3 directly with a line-to-line reading overstates the power by 73%, which can dangerously undersize a breaker or oversize a motor.
The line-to-neutral version of the formula uses a plain 3 because each phase-to-neutral reading is independent, and there are simply three of them adding up.
The Amps Check: Maximum Power at Unity Power Factor
The calculator shows the power your amps could deliver if the power factor were a perfect 1. Think of it as a sanity check on your result: your real wattage can never exceed this number.
For example, 400 volts at 50 amps gives a maximum of 34,641.02 watts at unity power factor. If your power factor is 0.85, the real power is 29,444.86 watts, comfortably below the ceiling. The gap between the two is the reactive power your supply must still carry.
Use this check when a result looks suspicious. If your calculated watts are close to or above the unity-power-factor figure, one of your inputs is wrong, usually the voltage type setting.
Common 3 Phase Wattage Mistakes
The biggest mistake is mixing up voltage types, as described above. Always confirm whether your 400, 415, 208, or 480 volt figure is line-to-line before trusting the answer.
The second mistake is entering power factor as a percentage. The calculator expects 0.85, not 85. Entering 85 would fail validation, but entering 0.85 when you meant 85% is a quieter trap, so double-check the decimal point.
The third mistake is using nameplate full-load amps for a lightly loaded motor. A motor running at half load draws far less than its nameplate current, so measure the actual current with a clamp meter when accuracy matters.
Where 3 Phase Power Calculations Are Useful
Motor sizing is the classic use. Before buying a motor, a contactor, or a variable-frequency drive, you compute the wattage from expected volts, amps, and power factor to make sure every component is rated for the real load.
Generator sizing is another. A standby generator must cover the kVA of everything running at once, so the calculator’s apparent-power figure tells you how big a generator to rent or buy.
Energy audits use the same math in reverse. Facilities teams measure volts and amps on each feeder, apply typical power factors, and build a picture of where the kilowatt-hours are going.
How to Interpret Your Result Correctly
Treat the watt figure as the working power and the kVA figure as the supply burden. Your bill follows the watts; your breaker, cable, and transformer sizes follow the kVA.
Remember that the answer is only as good as the inputs. A guessed power factor gives a ballpark, while measured volts, amps, and power factor from a power analyzer give an engineering answer.
Finally, this calculator covers balanced three-phase loads, where each phase carries the same current. Unbalanced loads need per-phase math, though the balanced result is still a useful approximation.
Worked Example: 400 V, 50 A, 0.85 PF (Line-to-Line)
First, list the inputs. V = 400 volts line-to-line, I = 50 amps, PF = 0.85.
Then, multiply the base. √3 × 400 × 50 = 1.73205 × 20,000 = 34,641.02 volt-amps. This is the apparent power, shown as 34.64 kVA.
Next, apply the power factor. 34,641.02 × 0.85 = 29,444.86 watts of real power.
Now, convert. 29,444.86 ÷ 1,000 = 29.44 kW. The amps check confirms 34,641.02 watts is the ceiling at PF = 1, and 29,444.86 sits properly below it.
Worked Example: 208 V, 30 A, 0.9 PF (Line-to-Line)
First, list the inputs. V = 208 volts line-to-line, I = 30 amps, PF = 0.9.
Then, find the apparent power. √3 × 208 × 30 = 1.73205 × 6,240 = 10,808.00 volt-amps, or 10.81 kVA.
Next, apply the power factor. 10,808.00 × 0.9 = 9,727.20 watts.
Finally, convert to kilowatts. 9,727.20 ÷ 1,000 = 9.73 kW. This is a typical draw for a small commercial rooftop AC unit.
Worked Example: 230 V Line-to-Neutral, 20 A, 0.8 PF
First, note the voltage type. 230 volts measured phase-to-neutral means the calculator must use the 3 × V formula, so select line-to-neutral in the dropdown.
Then, compute the base. 3 × 230 × 20 = 13,800 volt-amps, or 13.80 kVA.
Next, apply the power factor. 13,800 × 0.8 = 11,040.00 watts.
Finally, convert. 11,040.00 ÷ 1,000 = 11.04 kW. Using the line-to-line formula here by mistake would have given about 19,122 watts, nearly double, which shows why the dropdown matters.
Worked Example: 480 V, 100 A, 1.0 PF (Line-to-Line)
First, list the inputs. V = 480 volts line-to-line, I = 100 amps, PF = 1.0, a pure heating load.
Then, compute. √3 × 480 × 100 × 1.0 = 1.73205 × 48,000 = 83,138.44 watts.
Next, convert. 83,138.44 ÷ 1,000 = 83.14 kW, and apparent power is 83.14 kVA as well.
Finally, check the ceiling. At PF = 1 the real power equals the amps-check maximum exactly, 83,138.44 watts. Every amp is doing work, as expected for heaters.
Frequently Asked Questions
1. What is the 3 phase wattage formula?
For line-to-line voltage, the formula is P = √3 × V × I × PF. For line-to-neutral voltage, it is P = 3 × V × I × PF. V is volts, I is amps per phase, and PF is the power factor. Divide the result by 1,000 to get kilowatts.
2. What is the difference between watts and kVA?
Watts measure real power, the energy that does useful work. kVA measures apparent power, which includes reactive power that flows back and forth without doing work. The ratio between them is the power factor: kW ÷ kVA = PF. You pay for watts, but you size wires and transformers for kVA.
3. What power factor should I enter if I do not know it?
Use 0.85 for a typical motor running under normal load, which is the calculator’s suggested placeholder. Use 1.0 for pure heating loads like electric furnaces and water heaters. For an accurate result on an important job, measure the real power factor with a clamp meter or power analyzer.
4. Should I use line-to-line or line-to-neutral voltage?
Use line-to-line if your voltage reading was taken between two phase wires, which is the standard way nameplates and meters report three-phase voltage (for example 400 V or 480 V). Use line-to-neutral only if you measured from one phase to neutral (for example 230 V on a lighting circuit). The calculator picks the matching formula.
5. Why does the formula use the square root of 3?
The three voltage waveforms peak at different times, 120 degrees apart. When you measure across two phases, the vector sum of the two waveforms produces the √3 factor (about 1.732). It is a geometric result of how three-phase power is generated, not an arbitrary constant.
6. What is the amps check in the results?
The amps check shows the maximum power your entered current could deliver if the power factor were a perfect 1. Your real wattage must always be at or below this ceiling. If your result is close to or above it, one of your inputs, usually the voltage type setting, is wrong.
7. Can I use this calculator for single-phase loads?
Not directly. Single-phase real power is simply P = V × I × PF with no √3 and no factor of 3. Using this calculator on a single-phase load would overstate the power, so use a single-phase formula instead.
8. What does a power factor of 1 mean?
A power factor of 1 means every amp of current is doing useful work, with no reactive power flowing back and forth. Resistive heaters have a power factor of 1. In that case watts equal volt-amps, and the calculator’s real power and apparent power figures match exactly.
9. How do I convert the result to horsepower?
Divide the watt figure by 746 to get mechanical horsepower. For example, 29,444.86 watts ÷ 746 = 39.47 HP of electrical input. Note that motor output horsepower is lower because motors are not 100% efficient, so divide further by the motor’s efficiency for shaft power.
10. Why is my kVA higher than my kW?
Because kVA includes reactive power while kW counts only real power. The two are equal only at a power factor of 1. At PF = 0.85, the kVA is about 18% higher than the kW, which is normal and expected for motor loads.
11. What current should I enter: measured or nameplate?
Measured current from a clamp meter gives the true draw right now. Nameplate full-load amps give the worst-case draw at full load. Use measured current for energy calculations and nameplate current for sizing breakers, contactors, and cables.
12. Does this calculator work for unbalanced loads?
It assumes a balanced load with equal current in all three phases, which covers the great majority of motors and heaters. For a heavily unbalanced load, measure each phase separately and compute per-phase power. The balanced result remains a useful approximation.
13. How is 208 V different from 400 V in the calculation?
Only the voltage number changes; the formula is identical. A 208 V, 30 A, 0.9 PF load draws 9,727.20 W, while the same current and power factor at 400 V would draw proportionally more. Higher voltage delivers more power at the same current, which is why industrial sites prefer it.
14. Can power factor be greater than 1?
No. Power factor is a ratio that cannot exceed 1, and the calculator rejects any entry above 1. Values between 0 and 1 are valid, with most real loads falling between 0.7 and 1.0. A leading power factor from overcorrected capacitors is still expressed as a number at or below 1.
15. How accurate is the wattage result?
The math itself is exact for the inputs given. Accuracy in the real world depends on your measurements: a clamp meter reading and a known power factor give an engineering-grade answer, while guessed values give a ballpark. For billing or safety-critical sizing, measure all three quantities with proper instruments.