Subwoofer Enclosure Calculator
Design a sealed subwoofer box from the driver’s Thiele-Small parameters.
Found on the driver’s spec sheet, usually 0.2 – 0.7.
Equivalent compliance volume of the driver.
Free-air resonant frequency of the driver.
0.707 = flattest response (Butterworth). Higher = punchier but peakier.
Sealed (acoustic suspension) enclosure. Results are net internal air volume — add driver and bracing displacement to get the gross box size.
Building a subwoofer box by guessing is how good drivers end up sounding boomy, thin, or just wrong. The box is not a container — it is part of the speaker system. The air trapped inside acts as a spring that works with the driver’s suspension, and the volume of that air decides the system’s resonance, its low-frequency extension, and whether the bass sounds tight or bloated. The Subwoofer Enclosure Calculator above designs a sealed box from your driver’s Thiele-Small parameters: enter Qts, Vas, and Fs from the spec sheet plus your target box Q, and it returns the exact net internal volume, the system resonance, the −3 dB point, and even the internal edge length if you build a cube.
Sealed enclosures are the most forgiving box type for a first build. They have no port to tune, no port noise, and a gentle 12 dB-per-octave low-frequency rolloff that blends well with a car’s natural cabin gain or a room’s boundary reinforcement. What they demand instead is the right volume. Too small and the system Q rises, giving a peaked, one-note bass; too large and the Q falls, giving soft, overdamped bass with weak output. The calculator finds the volume that lands your chosen system Q exactly.
What the Subwoofer Enclosure Calculator Does
The calculator takes four inputs: the driver’s total Q factor (Qts), its equivalent compliance volume (Vas) in liters, its free-air resonant frequency (Fs) in hertz, and the target system Q (Qtc) you want the finished box to have. Qtc defaults to 0.707, the classic “maximally flat” alignment, but you can raise it for punchier bass or lower it toward the driver’s own Qts for a tighter, more controlled sound.
From these it computes the net internal air volume Vb in liters and cubic feet, the system resonant frequency Fc in hertz, the F3 point where output is 3 dB down, and the internal edge length of a cube box with that volume, in both centimeters and inches. It also shows each calculation step — the compliance ratio, the volume division, and the resonance multiplication — so you can check the math or learn how the formulas work.
How to Use the Calculator
Find the Thiele-Small parameters on your driver’s spec sheet or the manufacturer’s website. Enter Qts (typically between 0.2 and 0.7), Vas in liters (if your sheet lists cubic feet, multiply by 28.3168 first), and Fs in hertz. Then choose your target Qtc. If you leave it blank, the calculator uses 0.707.
Press Calculate. The most important rule the calculator enforces is that your target Qtc must be larger than the driver’s Qts. A sealed box can only raise the system Q above the driver’s own Q — it can never lower it — so asking for a Qtc below Qts is physically impossible, and the calculator explains this instead of returning a negative volume. Remember that Vb is the net air volume: the driver itself, any bracing, and the thickness of the walls all displace air, so your actual wooden box must be bigger than the number shown.
The Physics: Thiele-Small Parameters and the Sealed Box
Qts describes how underdamped the driver is at resonance — a high Qts driver rings more, a low Qts driver is more controlled. Vas is the volume of air that has the same compliance (springiness) as the driver’s suspension; it tells you how “stiff” the driver is in volume terms. Fs is the frequency where the driver naturally resonates in free air.
When you mount the driver in a sealed box, the trapped air adds a second spring in parallel with the suspension. The box volume relative to Vas sets the compliance ratio α = (Qtc ÷ Qts)² − 1, and the box volume follows directly: Vb = Vas ÷ α. A small box means a stiff air spring, a large α, and a high system Q; a large box means a soft spring and a Q close to the driver’s own. The system resonance rises above the driver’s Fs by the same ratio: Fc = Fs × (Qtc ÷ Qts). And the −3 dB frequency F3 is derived from Fc and Qtc — for the special case of Qtc = 0.707, F3 equals Fc exactly, which is why that alignment is so popular.
Worked Example 1: A Typical 10-Inch Driver
Take a driver with Qts = 0.35, Vas = 40 liters, and Fs = 30 Hz, with the default target Qtc = 0.707. Step by step:
First the ratio: Qtc ÷ Qts = 0.707 ÷ 0.350 = 2.020. The compliance ratio α = 2.020² − 1 = 4.0804 − 1 = 3.0804. Then Vb = Vas ÷ α = 40.00 ÷ 3.0804 = 12.99 liters, which is 12.99 ÷ 28.3168 = 0.459 cubic feet.
The system resonance Fc = Fs × 2.020 = 30.0 × 2.020 = 60.6 Hz. With Qtc = 0.707 the F3 point equals Fc, so F3 = 60.6 Hz as well — the response is flat down to about 61 Hz and then rolls off smoothly. For a cube box, the internal edge is the cube root of 12,990 cubic centimeters = 23.5 cm, or 9.25 inches. The calculator shows exactly these numbers, with each step listed so you can follow the arithmetic.
This is a small, practical box — under half a cubic foot — which is typical for a modern 10-inch driver with a moderately stiff suspension. Note how the sealed box raised the resonance from the driver’s 30 Hz free-air value to 60.6 Hz in the box; that shift is the air spring doing its work.
Worked Example 2: A Larger, Looser Driver
Now a different driver: Qts = 0.45, Vas = 60 liters, Fs = 28 Hz, still targeting Qtc = 0.707. The ratio is 0.707 ÷ 0.450 = 1.571, so α = 1.571² − 1 = 2.4684 − 1 = 1.4684. Then Vb = 60.00 ÷ 1.4684 = 40.86 liters, or 1.443 cubic feet — more than three times the volume of the first example, because this driver’s suspension is softer (larger Vas) and its Qts is higher, so less air-spring help is needed to reach the same system Q.
Fc = 28.0 × 1.571 = 44.0 Hz, and again F3 = 44.0 Hz at Qtc = 0.707. The cube edge is the cube root of 40,860 cm³ = 34.4 cm, or 13.56 inches. Comparing the two examples teaches the key lesson: drivers with high Vas and high Qts want big boxes, while low-Vas, low-Qts drivers are happy in small ones. There is no universal “correct” box size — only the correct size for your driver’s parameters.
Choosing Your Target Qtc
Qtc = 0.707 is the default because it gives the flattest frequency response before rolloff — the Butterworth alignment. It is the safest choice for music listening. A Qtc around 0.9 to 1.0 gives a mild bump in the upper bass that many listeners perceive as “punch,” at the cost of a slightly peaky, less accurate sound and a faster rolloff below the peak. Values above about 1.1 sound boomy and one-note, and are rarely desirable.
Going the other way, a Qtc of 0.6 or 0.577 (the Bessel alignment) gives an overdamped, extremely tight and controlled bass with the best transient response, but the box must be larger and the low-frequency output lower. Try entering 0.6 as your target Qtc for the first example driver and watch the required volume grow — that trade-off between box size and bass character is the central decision in sealed-box design.
Reading Your Results
The headline number is the net internal volume in liters, with cubic feet alongside for builders who think in imperial units. Treat it as the air the driver “sees.” Before cutting wood, add the driver’s own displacement (usually 1–3 liters for 10–12 inch drivers, listed on the spec sheet), plus bracing and any internal damping material displacement, to get the gross internal volume. Then add the wall thickness — 18 mm MDF on every side adds up fast — to get the external dimensions.
Fc tells you where the system’s resonance sits, and F3 tells you how low the flat response extends. Do not panic if F3 looks high: a sealed box’s gentle 12 dB/octave rolloff means there is still useful output an octave below F3, and in a car, cabin gain adds roughly 12 dB/octave below 60–70 Hz, which fills in the bottom beautifully. The cube edge is a starting point; you can reshape the same volume into any rectangular proportions you like as long as the net air volume stays the same.
Common Mistakes in Box Building
The classic mistake is building to gross external dimensions without subtracting wall thickness and driver displacement, ending up with a box 15–25% too small and a Qtc far higher than planned. Always work from net internal air volume outward. The second mistake is using Vas in the wrong units — mixing liters and cubic feet in the formula produces nonsense, so convert first.
A third mistake is chasing a Qtc below the driver’s Qts, which the calculator correctly refuses: you cannot make a sealed system more damped than the driver itself. Drivers with Qts above about 0.7 are poor sealed-box candidates at all; they want very large boxes or a different alignment. Finally, do not forget damping material: loosely filling the box with polyfill can make the driver behave as if the box were up to 15–20% larger, a useful trick if your built box came out slightly small.
Frequently Asked Questions
1. What are Thiele-Small parameters?
They are the standard electromechanical measurements that describe a speaker driver’s behavior: Qts (total damping), Vas (suspension compliance as an equivalent air volume), Fs (free-air resonance), and others. Nearly every box design calculation starts from them.
2. What is the formula for sealed box volume?
Vb = Vas ÷ ((Qtc ÷ Qts)² − 1). You choose the target system Q (Qtc), and the formula tells you the net internal air volume that produces it with your driver’s Qts and Vas.
3. Why must Qtc be greater than Qts?
A sealed box adds an air spring that can only raise the system’s total Q above the driver’s own Q — it cannot add damping. Requesting a Qtc at or below Qts would require a zero or negative box volume, which is physically impossible.
4. What does Qtc = 0.707 mean?
It is the Butterworth alignment: the flattest possible frequency response before the low-frequency rolloff, with good transient behavior. It is the default recommendation for music listening.
5. What is the difference between net and gross box volume?
Net volume is the air the driver actually sees. Gross volume adds the space displaced by the driver, bracing, and damping material, plus the wall thickness. Build from net volume outward, not the other way around.
6. What is Fc?
The resonant frequency of the driver once mounted in the box: Fc = Fs × (Qtc ÷ Qts). It is always higher than the driver’s free-air Fs because the trapped air stiffens the system.
7. What is F3?
The frequency where the system’s output has fallen 3 dB below the midband level — the conventional measure of useful bass extension. For Qtc = 0.707, F3 equals Fc.
8. Is a sealed box better than a ported box?
Neither is universally better. Sealed boxes are smaller, simpler, have no port noise, and roll off gently; ported boxes are larger and harder to design but play louder and deeper around their tuning frequency. This calculator covers sealed designs.
9. My driver has Qts = 0.8. Can I use a sealed box?
Technically yes, but the box would need to be enormous to reach a reasonable Qtc, and the result is rarely satisfying. High-Qts drivers are usually better suited to infinite-baffle or large ported designs.
10. Do I have to build a cube?
No. The cube edge is just a convenient reference. Any rectangular shape with the same net internal air volume performs identically — avoid only exact cubes if you are worried about internal standing waves, though at subwoofer frequencies this barely matters.
11. How does stuffing the box with polyfill change things?
Loose damping material slows sound inside the box, making the driver behave as though the box were up to 15–20% larger. It is a legitimate fine-tuning tool, not a substitute for a badly wrong volume.
12. Why does Vas matter so much?
Vas measures how stiff the driver’s suspension is, expressed as an air volume. A high Vas means a soft suspension that needs a large box; a low Vas means a stiff suspension that works in a small box. Box volume scales directly with Vas.
13. Can I use this for a home theater subwoofer?
Yes. The physics is identical whether the box goes in a car or a living room. Room gain in small rooms boosts the deep bass much like cabin gain does in cars, which flatters sealed designs.
14. What wall material and thickness should I use?
18 mm (3/4 inch) MDF is the standard: dense, non-resonant, and easy to work. Brace panels larger than about 30 cm across, seal every joint airtight with glue and screws, and make the driver cutout snug.
15. How accurate is the calculator?
The formulas are the exact classical sealed-box equations, so the math is as accurate as your inputs. Real-world results vary slightly with manufacturing tolerances in the driver’s parameters, temperature, and how airtight your build is.
Final Thoughts
A great subwoofer is a system, and the box is half of it. With your driver’s Qts, Vas, and Fs and a target Qtc in hand, the sealed-box formulas give you a precise, buildable volume instead of a guess — 12.99 liters for the example driver at a flat 0.707 alignment, 40.86 liters for the looser one. Build to the net air volume, seal the box airtight, and the bass will sound the way the math says it should: tight, controlled, and exactly as deep as you designed it to be.