Skip to content
Others

Vert Calculator

Vert Calculator

Enter a vert ramp’s height and transition radius to estimate drop-in speed, fall time, and whether the ramp is true vert or mini-ramp style.

ft
ft
The radius of the curved transition, not the ramp height. Measure it with the string method described below.

A vert ramp looks simple — two curved walls facing each other across a flat bottom — but the speed you carry at the bottom is pure physics. Drop in from the deck and gravity converts every foot of height into speed, whether you are ready for it or not. The calculator above estimates that drop-in speed, how long the fall takes, and what your transition radius says about the ramp, before you ever step on the coping.

What This Calculator Does

This tool takes two measurements — the ramp’s height from the flat bottom to the deck, and the radius of the curved transition — and turns them into four useful numbers. First, your estimated speed at the flat bottom after dropping in, shown in both feet per second and miles per hour, using the classic free-fall relation v = √(2gh). Second, the time the drop itself takes, from the moment you leave the deck until you reach the flat. Third, the length of the transition’s curved surface, handy if you are building or resurfacing. Fourth, a verdict on the ramp’s character: true vert, where the transition reaches vertical with extension above it, or mini-ramp style, where the curve tops out before vertical.

It is an estimator, not a speedometer. Real riding involves friction, pumping, and air resistance, so treat the numbers as the physics ideal — the speed gravity wants to give you — and read the “what the calculator leaves out” section before planning anything ambitious around them.

How to Use the Vert Calculator

Two measurements and one click stand between you and the numbers. Here is how to get each input right.

Step 1: Measure the Ramp Height

Measure straight down from the top of the deck (the platform you stand on) to the surface of the flat bottom, in feet. Do not measure along the curved transition — the calculator wants vertical height, because gravity only cares about how far you fall. A classic competition vert ramp is about 13 feet; backyard mini ramps are often 4 to 6 feet.

Step 2: Measure the Transition Radius

The transition radius is the radius of the imaginary circle the curved wall follows — not the height, not the width. The old builder’s trick is the string method: tie a string to a stake, hold the stake where the circle’s center would be, and swing the string along the transition; the string length that hugs the curve consistently is your radius. Typical vert ramp transitions run 8 to 10 feet; mini ramps are often 6 to 8 feet.

Step 3: Enter Both Numbers and Calculate

Type the height and radius into the fields and press Calculate. Both must be positive numbers in feet. If either field is empty or zero, the calculator shows an error instead of a result — it cannot estimate speed from a ramp with no height.

Step 4: Read Your Results

The headline number is your speed at the flat bottom. Below it, the breakdown shows the fall time, the transition arc length, the exact arithmetic, and the ramp-style verdict. Compare the verdict with what the ramp feels like — that comparison is how you calibrate your intuition for future ramps.

Step 5: Reset for Another Ramp

Press Reset to clear everything and run the numbers for a different ramp. Skaters who travel between parks find this useful: punch in each park’s specs and you will know, before your first drop-in, which ramp will feel fastest.

The Physics: Where v = √(2gh) Comes From

The speed formula is one of the cleanest results in physics, and it comes from conservation of energy. Standing on the deck, you hold gravitational potential energy equal to your mass times gravity times height (mgh). As you drop in, that stored energy converts into motion — kinetic energy, ½mv². Set them equal, mgh = ½mv², and something beautiful happens: the mass cancels out entirely. A 90-pound skater and a 200-pound skater drop in at the same speed, because gravity accelerates everything equally.

Solving for v gives v = √(2gh), with g = 32.2 ft/s² near Earth’s surface. Double the ramp height and your speed does not double — it grows by the square root of 2, about 1.41 times. That square-root relationship is why a 13-foot vert ramp feels so much more serious than a 5-foot mini ramp, yet not quite three times as fast: the math says √(13/5) ≈ 1.61 times the speed, and your instincts will confirm it.

The fall time comes from the same physics: t = √(2h/g). It answers a different question — not how fast, but how long the drop lasts. On a big ramp that fraction of a second is your entire window to get your feet set, which is why drop-ins feel so committed.

Worked Example: 11-Foot Ramp, 9-Foot Transition

Take a midsized vert ramp: 11 feet from flat bottom to deck, with a 9-foot transition radius. Here is the full arithmetic. Drop-in speed: v = √(2 × 32.2 × 11) = √708.4. The square root of 708.4 is 26.62, so you hit the flat bottom at 26.62 ft/s. Convert to miles per hour by multiplying by 0.6818: 26.62 × 0.6818 = 18.15 mph. That is bicycle-down-a-hill speed, on a skateboard, with your feet locked to the board by nothing but balance.

Fall time: t = √(2 × 11 ÷ 32.2) = √0.6832 = 0.83 seconds. Less than a second from deck to flat — which explains why a hesitant drop-in goes wrong so fast. Transition arc length: π × 9 ÷ 2 = 14.14 ft of curved surface per wall. And the ramp-style verdict: height (11) is greater than radius (9), so this is true vert — the transition reaches vertical, with 11 − 9 = 2.00 ft of vertical extension above the curve. That vert section is what lets riders go straight up and air back down.

Worked Example: 5-Foot Mini Ramp, 7-Foot Transition

Now a backyard mini ramp: 5 feet tall with a 7-foot transition radius. Speed: v = √(2 × 32.2 × 5) = √322.0 = 17.94 ft/s, which is 17.94 × 0.6818 = 12.23 mph. Fall time: t = √(2 × 5 ÷ 32.2) = √0.3106 = 0.56 seconds. So far, gentler in every way — about two-thirds the speed of the bigger ramp.

The interesting part is the verdict. Here the height (5) is less than the radius (7), so the transition never reaches vertical — this is mini-ramp style by definition. How steep does it get? The transition tops out at an angle θ where cos θ = 1 − h/r = 1 − 5/7 = 0.2857, which gives θ = 73.4°. The wall leans 73.4° from horizontal at the coping: steep enough to pump hard against, but not vertical, so airs launch slightly outward rather than straight up. That single number explains most of the difference in how the two ramps ride.

Understanding Your Results

Start with the speed, and translate it into something your body understands. Twelve mph is a fast sprint; 18 mph is a quick bicycle; 22+ mph — what a full 13-foot ramp produces — is serious velocity on four small wheels. If the number surprises you, trust the physics over your gut: most skaters underestimate how fast a tall ramp really is, which is exactly why drop-ins on unfamiliar ramps deserve respect.

The fall time tells you how committed each drop-in is. Under a second on most ramps, it is the window in which everything must go right — feet placement, shoulder alignment, weight forward. The transition arc length matters most to builders: multiply it by the ramp width to estimate surface material. And the ramp-style verdict is your riding preview — true vert means vertical walls and straight-up airs; mini-ramp style means mellower transitions and a more forgiving learning curve.

Transition Radius: Tight Versus Mellow

The radius is the ramp’s personality dial. A tight transition (small radius, say 6 feet on a tall ramp) whips you through the curve quickly — it feels aggressive, generates speed fast when you pump, and punishes mistakes. A mellow transition (large radius, say 10+ feet) spreads the turn over more distance, feels smoother and more predictable, and is kinder to beginners. Neither is objectively better; street-style skaters often prefer tighter transitions for the pop, while vert skaters like roomier curves at speed.

The relationship between radius and height is what the verdict analyzes. When the radius is smaller than the height, the curve finishes turning before the deck arrives, leaving vertical wall above it — the defining feature of a vert ramp. When the radius exceeds the height, the curve is still turning when it runs out of height, so the coping arrives early at some angle short of vertical. Both are legitimate ramps; they just ask for different riding.

Safety: Respect the Speed

These numbers are fun until they are not. Eighteen miles per hour on a skateboard leaves no margin for a loose truck, a pebble on the flat bottom, or a moment of hesitation at the coping. Wear a helmet every session — the speeds this calculator reports are easily enough to cause serious head injury in a fall — and add knee pads, elbow pads, and wrist guards when learning drop-ins. Inspect the ramp before riding: soft spots, popped-up screws, and wet surfaces all turn the estimated speed into a different, worse problem.

Build up gradually. If the calculator says an unfamiliar ramp will give you 20 mph at the bottom and your home ramp gives 12, do not drop in on the big one first — warm up on something closer to what you know. The physics does not care about your confidence level; it delivers the speed regardless.

What the Calculator Leaves Out

Honest estimates disclose their blind spots. The v = √(2gh) formula assumes a frictionless fall — no rolling resistance from wheels, no air drag, no energy lost to the flex of the ramp. Real drop-ins come in a little slower than the estimate, typically by a few percent on a well-kept ramp. It also ignores pumping: a skilled rider adds energy through the transition and arrives faster than gravity alone would deliver, while a stiff rider scrubs speed.

The fall-time estimate assumes you drop straight down, but a real drop-in follows the curved transition, which takes slightly longer than free fall. And none of this accounts for what happens after the flat bottom — your speed up the opposite wall depends on how cleanly you ride the transition. Use the numbers as the physics baseline, then let experience adjust them.

Common Mistakes When Sizing Up a Ramp

Measuring height along the curve. The tape must run vertically from deck to flat bottom. Measuring along the transition surface gives a longer number, which inflates the speed estimate.

Confusing radius with height. The two inputs describe completely different things: height is how far you fall, radius is how tightly the wall curves. Swapping them produces nonsense — a 9-foot “height” with an 11-foot “radius” describes a different ramp than the one you are standing on.

Mixing feet and meters. The calculator works in feet, the standard unit for ramp specs in the US skate scene. If you measured in meters, multiply by 3.281 to convert before entering — a 3.35-meter ramp is an 11-foot ramp, and entering 3.35 directly would wildly understate the speed.

Forgetting the flat bottom. The height is deck-to-flat, not deck-to-ground — on most ramps these are the same, but on elevated or uneven builds they differ, and the fall distance is what counts.

Treating the estimate as a guarantee. It is the speed of a perfect, frictionless drop-in. Your actual speed depends on your wheels, your pump, and the ramp’s condition. Fast is fun, but the estimate is a planning number, not a promise.

Frequently Asked Questions

1. What is a vert calculator?

It is a physics estimator for vert ramps — the big U-shaped skateboard and BMX ramps. You enter the ramp’s height and transition radius in feet, and it estimates your drop-in speed at the flat bottom, the fall time, the transition’s arc length, and whether the ramp is true vert or mini-ramp style.

2. How fast will I be going at the bottom of a vert ramp?

It depends on the height: speed follows v = √(2gh), so an 11-foot ramp gives about 26.6 ft/s (18.2 mph) and a 13-foot ramp gives about 28.9 ft/s (19.7 mph). Enter your ramp’s exact height in the calculator for its number — and remember it is a frictionless ideal, so real speeds run slightly lower.

3. What is the difference between a vert ramp and a mini ramp?

A vert ramp’s transition reaches vertical, with vertical wall (vert) above the curve — this happens when the ramp height is at least as large as the transition radius. A mini ramp’s transition tops out before vertical because its radius is larger than its height. The calculator’s verdict tells you which one your measurements describe.

4. How do I measure the transition radius?

Use the string method: anchor a string where the circle’s center would be and swing it along the transition — the string length that follows the curve evenly is the radius. Typical values are 8 to 10 feet for vert ramps and 6 to 8 feet for mini ramps. Do not confuse it with the ramp’s height.

5. Where is the height measured from?

Vertically from the top surface of the deck (the platform) straight down to the flat bottom’s surface, in feet. Measure plumb-vertical, not along the curved wall — gravity only cares about the vertical drop.

6. Does a heavier rider go faster?

No. In the v = √(2gh) formula, mass cancels out completely — gravitational potential energy (mgh) and kinetic energy (½mv²) both scale with mass, so it divides away. A lighter and a heavier rider drop in at the same speed, assuming equal friction and technique.

7. What does the “fall time” number mean?

It is the time a free-falling object would take to drop from the deck to the flat bottom, t = √(2h/g) — about 0.83 seconds for an 11-foot ramp. A real drop-in follows the curve and takes slightly longer, but the number captures how brief and committed the drop feels.

8. What is “vert” (vertical extension) on a ramp?

Vert is the section of vertical wall above the curved transition — the part that makes a vert ramp a vert ramp. When your ramp height exceeds the transition radius, the difference is vert: for example, an 11-foot ramp with a 9-foot radius has 2 feet of vert. It is what lets riders go straight up and air vertically.

9. Can I enter measurements in meters?

The calculator expects feet. Convert meters to feet first by multiplying by 3.281 — so a 3.35-meter ramp becomes 11 feet. Entering meters directly would massively understate the speed.

10. Why is my real speed lower than the estimate?

The formula assumes no friction, no air resistance, and no energy lost to ramp flex — a perfect fall. Real wheels have rolling resistance, bearings have drag, and stiff riding scrubs speed through the transition. Expect reality to run a few percent below the estimate on a well-maintained ramp.

11. What does a tight versus mellow transition feel like?

A tight (small-radius) transition turns quickly — it feels aggressive, generates speed fast when pumped, and punishes mistakes. A mellow (large-radius) transition spreads the turn out and feels smoother and more predictable. The radius input is what captures this personality difference.

12. How is the transition arc length useful?

Builders use it to estimate surface material: multiply the arc length by the ramp’s width to get the curved surface area per wall. For a 9-foot radius, each transition has about 14.14 feet of curved surface — double it for both walls, then multiply by width for the total.

13. Does pumping change the speed?

Yes. The calculator gives the speed gravity alone provides. A rider who pumps — extending and compressing through the transition — adds energy and arrives faster, while a stiff or hesitant rider scrubs speed. Technique can shift the result several percent in either direction.

14. Is it safe to drop in on any ramp this calculator describes?

The calculator describes physics, not safety. Speeds of 15 to 20+ mph demand a helmet, pads, a inspected ramp surface, and skills matched to the ramp. Build up from smaller ramps, warm up on something familiar, and never let the estimated number talk you into a drop-in you are not ready for.

15. What is a typical vert ramp size?

Competition vert ramps are usually 13 to 13.5 feet tall with 8 to 9-foot transitions and 1 to 2 feet of vert. Backyard mini ramps are typically 4 to 6 feet tall with 6 to 8-foot transitions. If your measurements land far outside these ranges, double-check them before trusting the results.

Final Thoughts

Knowing your speed before you drop in changes how you ride — it replaces guesswork with physics and bravado with preparation. Measure carefully, respect what the numbers tell you, wear your helmet, and work up to the big ramps one honest drop-in at a time. The ramp will always deliver the speed gravity promises; make sure your skills are there to meet it.