Skip to content
Internet

Synology Raid Calculator

Synology Raid Calculator

Enter your drives once — compare every RAID level side by side.

drives
TB

Choosing a RAID level feels like a gamble when every option trades capacity for safety in a different way. RAID 0 gives you everything and protects nothing; RAID 6 survives two failures but eats two drives; and the choices in between all look alike until you run the numbers. The Synology Raid Calculator ends the guessing: enter your drive count and drive size once, and it lays out all five RAID levels side by side — usable capacity, fault tolerance, and drive requirements in a single table. Compare first, then choose with confidence.

What This Calculator Does

Instead of calculating one RAID level at a time, this calculator shows you all five at once. You enter two numbers — how many drives you have and how big each one is — and it builds a comparison table covering RAID 0, RAID 1, RAID 5, RAID 6, and RAID 10. Each row shows the usable capacity, how many drive failures that level survives, and the minimum setup it needs. Rows your drive count cannot support are marked honestly instead of showing a misleading zero. It is the fastest way to answer “which RAID should I pick for my four 4 TB drives?” — because the answer sits in front of you in a single glance.

How to Use the Synology Raid Calculator

Type your number of drives and the size of each drive in terabytes, then press the Compare RAID Levels button. The table appears below with one row per RAID level. Every supported level shows its usable capacity in bold; rows marked “Not possible” explain what is missing — for example, RAID 6 with three drives will tell you it needs at least four. Try different drive counts to see how the winner changes: add a fifth drive and watch RAID 6 suddenly become viable, or switch from four to five drives and see RAID 10 drop out. The Reset button clears the table so you can compare another configuration from scratch.

How Each RAID Level Is Calculated

All five rows use the same two inputs — drive count (N) and drive size (S) — with a different formula behind each. RAID 0: N × S, every byte usable, zero protection. RAID 1: S, one drive’s worth of space, survives one failure. RAID 5: (N − 1) × S, needs three or more drives, survives one failure. RAID 6: (N − 2) × S, needs four or more drives, survives two failures. RAID 10: (N ÷ 2) × S, needs an even count of four or more drives, survives one failure per mirrored pair and offers the best speed of the protected levels. The pattern is simple: protection always costs drives, and the table shows you exactly what each level charges.

Worked Example With Full Arithmetic

Take 4 drives of 4 TB each. The raw total is 4 × 4 = 16 TB for every row, and from there each level diverges. RAID 0: 4 × 4 TB = 16 TB usable, survives 0 failures. RAID 1: one drive = 4 TB usable, survives 1 failure. RAID 5: (4 − 1) × 4 TB = 12 TB usable, survives 1 failure. RAID 6: (4 − 2) × 4 TB = 8 TB usable, survives 2 failures. RAID 10: (4 ÷ 2) × 4 TB = 8 TB usable, survives 1 failure per pair. The comparison makes the trade-off visible at a glance: RAID 5 gives you the most protected space here at 12 TB, while RAID 6 and RAID 10 both give 8 TB — RAID 6 with stronger failure protection, RAID 10 with better speed. Your choice comes down to which of those two strengths your data needs more.

Reading the Comparison Table

Read each row left to right: the RAID name, the usable capacity in terabytes, the number of simultaneous drive failures it survives, and the minimum setup it needs. Sort mentally by what matters most to you. If capacity is king, look for the biggest usable number among the protected levels. If your data is irreplaceable, look for “2 failures” first. If a row says Not possible, your current drive count rules that level out — the note tells you exactly what would fix it, like adding one more drive or making the count even. Run the table for the setup you own today and the setup you might buy tomorrow; the comparison often reveals that one extra drive unlocks a much better option.

Which RAID Level Should You Choose

For a typical home NAS with three or four drives holding photos and media, RAID 5 is the sweet spot — strong efficiency with single-drive protection. Choose RAID 6 when you have five or more drives, store business records, or use huge drives whose rebuilds take days; surviving two failures is worth the extra drive. Pick RAID 10 when speed is the priority — video editing, virtual machines, busy databases — and you can accept giving up half your space. RAID 1 fits simple two-drive setups where simplicity wins. Reserve RAID 0 for scratch space you can lose without pain. And whatever you choose, remember that RAID is not a backup: it guards against drive failure, not against deletion, theft, or ransomware — keep a real copy of anything irreplaceable somewhere else.

Common Mistakes to Avoid

First, picking by capacity alone and ignoring fault tolerance — the cheapest terabyte is worthless if one failure takes your data with it. Second, assuming RAID is a backup; it is not, so keep a genuine copy of irreplaceable files elsewhere. Third, running RAID 5 on very large drives, where multi-day rebuilds raise the risk of a second failure striking mid-repair — RAID 6 exists for exactly this situation. Fourth, choosing RAID 10 with an odd number of drives, which is impossible by definition since the level works in mirrored pairs. Fifth, forgetting that a failed drive must be replaced promptly: every day you run in degraded mode is a day your protection is gone, so keep a spare drive on the shelf.

Frequently Asked Questions

1. Which RAID level gives the most usable capacity?

RAID 0 gives you 100 percent of your raw space, but with zero protection — one failed drive loses everything. Among levels that actually protect your data, RAID 5 gives the most usable capacity for three or more drives.

2. Which RAID level is safest for a home NAS?

RAID 6 is the safest common choice because it survives two simultaneous drive failures. For a typical home NAS with three or four drives, RAID 5’s single-drive protection is usually enough — step up to RAID 6 once you have five or more drives.

3. Is RAID 5 still safe with large modern drives?

It is less comfortable than it used to be. Rebuilding a failed 12 TB or larger drive can take days, and a second failure during that window destroys the array. With drives of 8 TB and above, RAID 6 is the more responsible choice.

4. What is the difference between RAID 5 and RAID 6?

RAID 5 keeps one drive’s worth of parity and survives one failure: usable = (N − 1) × S. RAID 6 keeps two drives’ worth of parity and survives two failures: usable = (N − 2) × S. RAID 6 costs one extra drive but is far tougher during rebuilds.

5. When should I choose RAID 10 over RAID 6?

Choose RAID 10 when speed matters more than maximum protection — video editing, virtual machines, and busy databases all benefit from its fast writes. Choose RAID 6 when surviving two drive failures matters more than speed, which is the case for most archives and backups.

6. Can I use RAID 1 with four drives?

RAID 1 is a two-drive mirror, so with four drives you would use RAID 10 instead — it mirrors in pairs and stripes across them, giving you the same protection concept with much better performance and 2 drives’ worth of usable space.

7. Why does RAID 10 need an even number of drives?

RAID 10 builds mirrored pairs first, then stripes data across the pairs. A leftover odd drive cannot join a pair, so the drive count must be even — 4, 6, 8, and so on.

8. Does RAID protect my files from accidental deletion?

No. RAID mirrors your mistakes as faithfully as your data — a deleted file is deleted on every drive instantly. RAID protects against hardware failure only; protection against deletion, ransomware, and theft requires a real backup.

9. How long does a RAID rebuild take?

It depends on drive size and NAS load: small drives finish in hours, while 12 TB and larger drives can take several days. During a rebuild the array is vulnerable, which is why RAID 6’s second parity drive is so valuable with big drives.

10. Can I mix RAID levels on one Synology NAS?

Yes. A Synology NAS can hold multiple storage pools, and each pool can use its own RAID level — for example, RAID 10 for speed-hungry work and RAID 6 for long-term archives on the same box.

11. What is the best RAID level for two drives?

RAID 1, without question. It mirrors your data so either drive can fail without loss, giving you one drive’s worth of usable space. Synology’s SHR is equally good here and makes future expansion easier.

12. What is the best RAID level for six drives?

RAID 6 for most people — with six drives you get four drives’ worth of usable space plus two-drive failure protection. Pick RAID 10 instead only if you need maximum write speed and can accept three drives’ worth of space.

13. Does RAID make my NAS faster?

Striped levels read faster because data comes from several drives at once — RAID 0, 5, 6, and 10 all beat a single drive for reads. Writes are a mixed picture: RAID 10 writes quickly, while RAID 5 and especially RAID 6 pay a parity penalty on every write.

14. What happens when a drive fails in each RAID level?

The array drops into degraded mode but keeps running on RAID 1, 5, 6, and 10 while you replace the drive — RAID 6 even survives a second failure during the repair. On RAID 0 there is no degraded mode: one failed drive means the entire volume and all its data are gone.

15. Should I keep a spare drive on the shelf?

Yes — a cold spare of the same size and model is one of the cheapest insurance policies in storage. It lets you start the rebuild the hour a drive fails instead of waiting days for a delivery while your array runs without full protection.

Final Thoughts

There is no single best RAID level — only the best one for your drives and your data. The comparison table turns an abstract trade-off into concrete numbers: terabytes you gain, failures you survive. Run your own drive count through the Synology Raid Calculator, weigh capacity against safety honestly, and pick the row that lets you sleep at night. Then back up what matters — because even the toughest RAID array is no substitute for a real backup.