Synology Disk Calculator
An 8 TB drive never gives you 8 TB. Enter the disk size, file system, and sector format to see the true formatted, usable capacity of a single drive.
The size printed on the box or the retail listing, in decimal terabytes.
Btrfs reserves more space for metadata, checksums, and snapshots than ext4.
Modern large drives are 4Kn. Some older or shingled drives report 512e sectors.
You buy an 8 TB hard drive, slide it into your Synology NAS, and Storage Manager reports barely 7.16 TiB of usable space. Nothing is broken and nothing is missing. Three quiet deductions happened before your first file ever landed on the disk: the industry counts a terabyte differently than your computer does, Synology reserves a slice of every disk for its own system partition, and formatting the disk with a file system costs a little more. The Synology Disk Calculator above measures all three deductions for a single drive. Enter the advertised disk size, choose Btrfs or ext4, and pick the sector format, and it shows the true formatted, usable capacity of that one disk, plus exactly where the rest went.
What This Tool Measures
This calculator answers a per-disk question: how much space does one physical drive actually give you inside a Synology NAS? It starts from the advertised size printed on the box, converts it to the binary units your NAS reports, subtracts the DSM system partition that Synology carves out of every drive, and then subtracts the formatting overhead of the file system and sector layout you chose. The result is the usable capacity of that single disk before any RAID or SHR redundancy is applied. That distinction matters. This is not a RAID planner and it does not combine multiple drives; it tells you the honest size of one drive so that every later capacity plan you make starts from a true number instead of the box number.
How to Use the Synology Disk Calculator
Enter the disk size exactly as advertised, in decimal terabytes: 4, 8, 12, 16, 18, 20, or 22 are the common retail sizes. Next, choose the file system you plan to use. Btrfs is the default on modern Synology models and the right choice for snapshots and data integrity, while ext4 is the leaner classic option on some models and older units. Then choose the sector format: 4Kn for 4K native drives, which covers nearly all current large hard drives, or 512e for drives that emulate 512-byte sectors, which is common on some older and shingled models. Press Calculate and the tool shows the usable capacity per disk in large type, with a breakdown of the advertised capacity in TiB, the DSM system partition reservation, the formatting overhead as a percentage and a TiB amount, and the usable space in both TiB and GB. If an input is invalid, the calculator explains what to fix.
The Capacity Formula Explained
The calculation runs in four steps. Step one converts the advertised size to binary units. Drive makers define 1 TB as 1,000,000,000,000 bytes, but operating systems report space in tebibytes, where 1 TiB equals 1,099,511,627,776 bytes. The conversion factor is (1000 ÷ 1024)³, which is about 0.9095, so an advertised 8 TB drive is 8 × 0.9095 = 7.28 TiB before anything else happens. Step two subtracts the DSM system partition. Synology reserves roughly 2.4 GB on every drive for the DSM system partition, which holds the operating system and runs RAID 1 across all installed disks, so one disk can fail without losing the system. In TiB that reservation is about 0.0022 TiB: small, but real.
Step three subtracts formatting overhead, which depends on your two choices. Btrfs carries about 1.5 percent overhead because it keeps checksums for data integrity, metadata trees, and room for its snapshot machinery. The ext4 file system is leaner at about 0.5 percent. The sector format adds a little more: 4Kn drives add nothing, while 512e emulation adds about 0.3 percent because of alignment padding. So the total overhead rate is 1.5 percent for Btrfs on 4Kn, 1.8 percent for Btrfs on 512e, 0.5 percent for ext4 on 4Kn, and 0.8 percent for ext4 on 512e. Step four applies that rate to the space left after the DSM reservation: usable = (advertised TiB − DSM reservation) × (1 − overhead rate). That is the number Storage Manager will effectively give you from the drive.
Worked Examples
Example one. An 8 TB drive formatted with Btrfs on 4Kn sectors, the most common modern setup. Step one, convert the advertised size: 8 × 0.9095 = 7.28 TiB. Step two, subtract the DSM system partition of about 0.0022 TiB: 7.28 − 0.0022 = 7.27 TiB. Step three, the overhead rate is 1.5 percent for Btrfs plus 0 percent for 4Kn, so the overhead is 7.27 × 0.015 = 0.11 TiB. Step four, usable space is 7.27 − 0.11 = 7.16 TiB, which is about 7,337 GB. The calculator shows 7.16 TiB as the usable capacity per disk. Nearly 0.84 TB of the advertised 8 TB went to unit conversion, the system partition, and formatting.
Example two. A 4 TB drive formatted with ext4 on 512e sectors. Step one, convert: 4 × 0.9095 = 3.64 TiB. Step two, subtract the DSM reservation: 3.64 − 0.0022 = 3.64 TiB. Step three, the overhead rate is 0.5 percent for ext4 plus 0.3 percent for 512e, a total of 0.8 percent, so the overhead is 3.64 × 0.008 = 0.03 TiB. Step four, usable space is 3.64 − 0.03 = 3.61 TiB, about 3,693 GB. The calculator shows 3.61 TiB. The leaner ext4 file system keeps more of the drive, which is why older or smaller NAS setups sometimes prefer it.
Example three. A 16 TB drive formatted with Btrfs on 4Kn sectors. Step one, convert: 16 × 0.9095 = 14.55 TiB. Step two, subtract the DSM reservation: 14.55 − 0.0022 = 14.55 TiB. Step three, the overhead is 14.55 × 0.015 = 0.22 TiB. Step four, usable space is 14.55 − 0.22 = 14.33 TiB, about 14,675 GB. The calculator shows 14.33 TiB. Notice the pattern: the unit conversion alone takes about 9 percent of every drive, while the file system and sector choices move the final number by roughly one percent.
Understanding Your Results
The headline number is the usable capacity of the single disk: the space your files, apps, and shared folders can actually occupy on that drive before redundancy. The advertised capacity row shows the same drive measured in TiB, which is the number that makes the box size look smaller and is the fairest starting point for planning. The DSM system partition row confirms the 2.4 GB reserved on every disk; it is not wasted space, because it hosts the DSM operating system mirrored across your drives. The formatting overhead row shows the combined percentage and TiB cost of your file system and sector choices, which is the one part of the calculation you can influence. The final row restates the usable space in TiB and in GB, handy when you are comparing drives at the store. If you are planning a multi-drive pool, take this per-disk number and feed it into a RAID capacity planner as the true size of each drive.
Common Mistakes to Avoid
The most common mistake is planning a NAS build around the box number. If you budget 32 TB from four 8 TB drives, you will actually land near 28.7 TiB of raw per-disk space before redundancy, and the shortfall only grows from there. The second mistake is forgetting the DSM system partition exists and assuming the TiB conversion is the whole story; it is small, but on small drives it is visible. The third mistake is choosing Btrfs and expecting ext4-level efficiency: Btrfs costs about one extra percent of every disk, a fair price for checksums and snapshots, but a price worth knowing. The fourth mistake is ignoring the sector format on older drives: a 512e drive quietly costs another 0.3 percent through alignment overhead. The fifth mistake is treating this per-disk number as pool capacity; RAID and SHR redundancy subtract whole drives of space on top of everything calculated here. Finally, remember that usable capacity is not the same as available capacity: once the NAS is running, services, apps, and snapshots consume space from this total too.
Frequently Asked Questions
1. Why does my 8 TB drive only show about 7.16 TiB?
Three deductions apply. The decimal-to-binary conversion turns 8 TB into 7.28 TiB, the DSM system partition reserves about 2.4 GB, and Btrfs formatting takes about 1.5 percent. Together they leave roughly 7.16 TiB of usable space.
2. What is the difference between TB and TiB?
A terabyte (TB) is 1,000,000,000,000 bytes, the decimal unit drive makers use. A tebibyte (TiB) is 1,099,511,627,776 bytes, the binary unit operating systems use. One advertised TB equals about 0.9095 TiB, so the drive always looks smaller in the NAS.
3. What is the DSM system partition?
Synology reserves about 2.4 GB on every installed drive for a system partition that holds the DSM operating system. It is mirrored across all drives, so your NAS keeps working even if one disk fails.
4. Does Btrfs or ext4 give me more usable space?
ext4 gives slightly more, because its formatting overhead is about 0.5 percent versus about 1.5 percent for Btrfs. Most users still choose Btrfs for its checksums and snapshots, which are worth the small space cost.
5. What is the difference between 4Kn and 512e sectors?
4Kn drives use 4,096-byte native sectors, the modern standard for large drives. 512e drives have 4K physical sectors but emulate 512-byte sectors for older systems, which adds a small alignment overhead of about 0.3 percent.
6. How do I check my drive’s sector format?
In DSM, open Storage Manager, select a drive, and look at its details, or check the drive manufacturer’s specification sheet. Most current NAS hard drives above 4 TB are 4Kn.
7. Does this calculator include RAID redundancy?
No. It calculates the usable capacity of one physical disk. RAID and SHR redundancy, which protect against whole-drive failure, are a separate layer calculated by a RAID capacity planner.
8. How much space does Btrfs formatting use?
About 1.5 percent of the drive, which covers metadata trees, data checksums, and headroom for the snapshot system. On an 8 TB drive that is roughly 0.11 TiB.
9. Can I avoid the DSM system partition reservation?
No, it is automatic and required. Every drive Synology initializes gets the system partition, and it is what lets DSM boot and keep running when a disk fails.
10. Why do two identical drives sometimes show slightly different sizes?
Manufacturing tolerances, different firmware, and sector remapping can shift a drive’s exact sector count by a tiny amount. The calculator uses the advertised size, so real drives may differ by a fraction of a percent.
11. Should I buy bigger drives to make up the difference?
Often yes. Since roughly 9 percent disappears in the TB-to-TiB conversion alone, sizing up one step, for example from 8 TB to 10 or 12 TB drives, is the simplest way to hit a real capacity target.
12. Does the calculator work for SSDs too?
The unit conversion and DSM partition math apply to SSDs as well, but SSDs also reserve over-provisioning space that varies by model, so treat the result as a close estimate rather than an exact figure for solid-state drives.
13. What does the GB figure in the results mean?
It is the same usable capacity expressed in gigabytes, which is useful when comparing drives at retail, since some sellers and tools still quote sizes in GB.
14. Will snapshots reduce this number further?
Yes. Snapshot reserve is taken from the usable space calculated here, not included in it. If you plan heavy snapshot use, budget extra space beyond this per-disk figure.
15. Is the advertised size a lie?
No, it is just a different unit. The drive really does hold 8,000,000,000,000 bytes. Your NAS simply reports that count in tebibytes, a larger unit, so the number looks smaller.
Final Thoughts
Every drive you buy for a Synology NAS pays three small taxes before it stores a single file: the decimal-to-binary conversion, the DSM system partition, and the formatting overhead of your file system and sector layout. The Synology Disk Calculator makes those taxes visible for one drive at a time, so you can compare drives honestly, choose between Btrfs and ext4 with open eyes, and plan your storage around true numbers instead of box numbers. Measure each disk first, then plan the pool. Your future self, staring at Storage Manager, will thank you.