Privacy Fence Cost Calculator
Estimate the installed cost of your privacy fence, including gates.
Your Cost Estimate
A privacy fence is one of the fastest ways to turn an overlooked backyard into a space you actually use. But quotes from contractors can swing by thousands of dollars, and it is hard to know what is fair without a baseline. This calculator gives you that baseline: a line-by-line installed cost estimate for a privacy fence built from wood, vinyl, or composite, with gates included.
It is built for planning, not for ordering lumber. Instead of a materials shopping list, you get installed per-foot pricing that already reflects both materials and labor, so the number you see is close to what a contractor would charge for a straightforward job.
What This Calculator Does
Enter your fence length in linear feet, pick 6-foot or 8-foot height, choose wood, vinyl, or composite, and add the number of walk gates you need. The calculator multiplies your length by the installed per-foot rate for that material and height, adds $250 per installed gate, and shows you a line-item breakdown plus the total.
The per-foot rates cover a typical professional installation: panels or pickets, posts set in concrete, hardware, and labor. They assume a reasonably flat yard and a simple rectangular run, which fits most suburban privacy fence projects.
How to Use This Calculator
Measure your fence line in linear feet. For a rectangular yard, add up the sides you plan to fence – most people skip the side with the house. If you are unsure, pace it off: one adult step is roughly 2.5 feet, so 40 steps is about 100 feet.
Choose your height. Six feet is the standard privacy fence and is allowed almost everywhere. Eight feet gives maximum seclusion but check your local rules first, because many cities cap residential fences at 6 feet in side and back yards.
Pick your material based on budget and how much maintenance you want to do, then enter the number of single walk gates. Count every opening you need: front access, side access, and anywhere you will wheel a mower or trash bins through. Click Estimate Cost to see your breakdown.
What “Installed Cost Per Foot” Includes
Installed per-foot pricing bundles everything a contractor brings: the fence material itself, pressure-treated or steel posts, concrete for the footings, screws and brackets, and the crew’s labor to dig, set, level, and finish the run. That is why installed prices look much higher than the price of pickets at the lumber yard.
Privacy fences cost more per foot than open picket or chain-link fences for a simple reason: they use far more material. A 6-foot solid fence needs roughly twice the lumber of a 3-foot spaced picket fence, plus sturdier posts to handle wind load. Going from 6 feet to 8 feet adds about a third to the per-foot cost, because of the extra material and deeper post holes.
The calculator’s rates reflect typical US pricing for straightforward jobs on flat ground: wood at $45 per foot for 6 feet and $60 for 8 feet, vinyl at $70 and $85, and composite at $80 and $95. Gates are priced at $250 each installed, which covers the gate frame, hinges, latch, and the extra-strong posts a gate needs.
Worked Example 1: 150 Feet of Wood Fence With 2 Gates
You want to fence three sides of a backyard: 150 linear feet of 6-foot pressure-treated wood, with 2 walk gates. The 6-foot wood rate is $45 per installed foot.
Fence cost: 150 ft x $45 = $6,750. Gate cost: 2 gates x $250 = $500. Total: $6,750 + $500 = $7,250. The breakdown shows you exactly where the money goes, so if a contractor quotes $9,500 for the same job, you know to ask what the extra $2,250 covers – maybe difficult soil, old fence removal, or just a higher margin.
Worked Example 2: 80 Feet of 8-Foot Composite With 1 Gate
A smaller yard needs only 80 linear feet, but you want maximum privacy and zero maintenance, so you choose 8-foot composite at $95 per installed foot, plus 1 walk gate.
Fence cost: 80 ft x $95 = $7,600. Gate cost: 1 x $250 = $250. Total: $7,600 + $250 = $7,850. Notice how the taller height and premium material make a short run cost more than the 150-foot wood fence in the first example. Material and height choices move the total more than length does.
Wood vs Vinyl vs Composite: Which Should You Pick?
Wood is the cheapest way in, at $45 to $60 per installed foot. Pressure-treated pine lasts 10 to 15 years with basic care, and cedar looks better and lasts longer but costs more. The tradeoff is maintenance: expect to stain or seal wood every 2 to 3 years, and replace the occasional warped picket.
Vinyl costs $70 to $85 per foot installed but needs almost no upkeep – no painting, no staining, no rot. It lasts 20 to 30 years and just needs an occasional wash. The downside is a higher upfront price and fewer style options, though modern vinyl looks much better than the shiny plastic fences of the past.
Composite, at $80 to $95 per foot, is the premium choice. It mimics wood grain convincingly, resists rot and insects like vinyl, and carries the longest warranties. If you plan to stay in your home for decades and want the fence to look great the whole time, composite is worth pricing out.
How to Read Your Results
The first line shows your material, height, and the per-foot math, for example “Vinyl 6 ft – 120 ft x $70.00” with the line total beside it. The second line shows your gates the same way. The total is the sum: your planning budget for a straightforward installation.
Use the total as a negotiating baseline, not a final quote. Real quotes will vary with your soil, slope, access, and local labor rates. If two contractors bid within 10 to 15 percent of this estimate, both are probably in the right range; if one is far off, ask why.
Ways to Keep the Cost Down
Fence only what you need. Many homeowners fence the backyard and leave the front open, which can cut 30 to 40 percent off the length. Keep the layout simple: every corner and every gate adds labor, so a straight run is the cheapest fence per foot.
Stick with 6 feet unless you truly need 8. The taller fence costs about a third more per foot and may trigger permit hassles. Minimize gates, since each one costs $250 installed and needs beefier posts. Finally, get at least three quotes and schedule the work in the contractor’s slower season – late fall and winter bids often come in lower.
Common Mistakes When Budgeting a Fence
The biggest mistake is budgeting from material prices alone. A homeowner sees pickets at a few dollars each and estimates $2,000, then gets a $7,000 installed quote and feels cheated. Labor, posts, concrete, and gates are roughly half the job – this calculator includes them so you are not surprised.
People also forget gates, permits, and old fence removal. A permit can cost $50 to $200, and hauling away an old fence can add several hundred dollars. Sloped yards are another budget killer: stepping or racking a fence on a hill adds significant labor. Always tell contractors about slopes and existing fences when getting quotes.
Frequently Asked Questions
1. How much does a privacy fence cost per foot installed?
Typical installed prices are $45 to $60 per linear foot for wood, $70 to $85 for vinyl, and $80 to $95 for composite, with 8-foot fences costing more than 6-foot ones. Gates add about $250 each. Use the calculator above with your length to get a total.
2. How do I measure linear feet for a fence?
Measure each side you plan to fence and add them together. A tape measure is best, but pacing works for estimates: one adult step is about 2.5 feet. Do not subtract for gates – the calculator handles those separately.
3. Is a 6-foot or 8-foot fence better?
Six feet is the standard: it blocks sight lines for most yards, costs less, and is legal almost everywhere. Eight feet gives true seclusion but costs about a third more per foot and may exceed local height limits, so check your city rules first.
4. Why is the installed price so much higher than lumber prices?
Because you are paying for a finished job, not raw boards. Posts, concrete, hardware, and skilled labor to dig, set, and level everything typically make up about half the total. The per-foot rates in this calculator already include all of that.
5. How many gates do I need?
Most homes need at least one or two: front access and a side or rear opening for mowers and trash bins. Walk through your daily routine – every path you take with equipment or bins probably deserves a gate. Each additional gate adds about $250 installed.
6. What is the cheapest privacy fence material?
Pressure-treated pine is the cheapest installed option at about $45 per foot for a 6-foot fence. It lasts 10 to 15 years with regular staining. If you skip maintenance, it will look tired much sooner, so factor in the upkeep.
7. Is vinyl worth the extra cost over wood?
Often yes, if you value your time. Vinyl costs roughly $25 more per foot installed than wood but needs no staining and lasts 20 to 30 years. Over the fence’s life, the maintenance savings usually cover the price difference.
8. Does the estimate include permits?
No. Permits typically cost $50 to $200 depending on your city, and some homeowners associations have their own approval process. Check local requirements before you build – an 8-foot fence especially may need a variance.
9. What about removing an old fence?
Removal and disposal usually cost a few hundred dollars on top of the new fence, depending on length and material. Ask each contractor whether their quote includes tear-out, because some leave it out and surprise you later.
10. Does a sloped yard cost more?
Yes. Fences on slopes must be stepped or racked, which takes more labor and sometimes more material. Mention any significant slope when getting quotes, and expect the final price to run above this calculator’s flat-yard estimate.
11. How long does installation take?
A professional crew usually finishes 100 to 200 linear feet in one to three days, depending on soil, weather, and gates. DIY projects take considerably longer, especially digging post holes by hand.
12. Should I build it myself to save money?
DIY can cut the total roughly in half, but fence building is harder than it looks – straight, level, properly set posts are a real skill. A leaning fence is expensive to fix. If you DIY, rent an auger and take your time with the layout.
13. Will a privacy fence raise my property value?
It can help, especially for families with kids or dogs who value a secure yard. You rarely recover the full cost at resale, so build it for your own enjoyment first and treat any value bump as a bonus.
14. How do I know if a contractor’s quote is fair?
Compare it against this calculator’s estimate and get at least three written quotes. Quotes within 10 to 15 percent of the estimate are normal; big outliers in either direction deserve questions about what is included or left out.
15. Can I use this estimate for a commercial property?
It gives a rough starting point, but commercial jobs often have different requirements: security specs, taller heights, and different materials. Get dedicated commercial quotes rather than relying on this residential planning estimate.
Final Thoughts
A privacy fence is a straightforward project once you know the numbers. Measure your length, pick a height and material that fit your budget and your tolerance for maintenance, and use the installed per-foot math to sanity-check every quote you get. Contractors respect an informed customer, and you will end up with a fence you love at a price you understand. Happy building.