Skip to content
tool

Pixel Pitch Calculator

LED VIDEO WALL PLANNER

Cabinet Pixel Pitch

Give the horizontal pixel count of one cabinet and its physical width. The planner returns the pixel pitch, the PPI equivalent, and a viewing-distance hint.

SINGLE CABINET

Count the LED pixels across one cabinet or module, left to right.

Measure the cabinet width in millimetres, edge to edge.

Walk up to a stadium screen, a concert backdrop, or a retail video wall and you are looking at thousands of LED cabinets bolted together. The single number that defines how sharp that wall looks is pixel pitch: the distance, in millimetres, between the centres of neighbouring pixels.

Pixel pitch decides the minimum viewing distance, the price per square metre, and whether the audience sees a smooth image or a grid of dots. A P2.6 wall and a P3.9 wall can look identical from far away and completely different up close.

This guide explains what pixel pitch means, how to calculate it from a cabinet’s pixel count and physical width, and how to use the Pixel Pitch Calculator above to get the pitch, the PPI equivalent, and a viewing-distance hint for any LED panel.

What Pixel Pitch Is

Pixel pitch is the centre-to-centre spacing of adjacent pixels, measured in millimetres. A pitch of 2.6 mm means every pixel sits 2.6 mm from its neighbours, horizontally and vertically. Smaller pitch means denser pixels and a sharper image at close range.

The industry names products after this number. A wall sold as P2.6 has a pitch of about 2.6 mm; P3.9 is about 3.9 mm; P10 is about 10 mm. The calculator above shows this catalogue name alongside the exact figure, so you can translate a measurement into the product label.

How Pixel Pitch Is Calculated

Take one cabinet or module and count the pixels across its width, then measure that width in millimetres. Divide the width by the pixel count and you have the pitch. Every cabinet in the wall shares the same pitch, so one measurement describes the whole display.

The formula is:

Pixel pitch (mm) = panel width (mm) / horizontal pixels

A 500 mm wide cabinet with 192 pixels across gives 500 divided by 192, which is 2.604 mm. The calculator rounds this to three decimals and also reports the PPI equivalent and a viewing-distance estimate.

Pixel Pitch and PPI Are Two Sides of One Coin

PPI, pixels per inch, is just pixel pitch expressed in imperial units. Since one inch equals 25.4 mm, the conversion is direct: PPI equals 25.4 divided by the pitch in millimetres. A 2.604 mm pitch converts to 9.75 PPI.

LED walls have startlingly low PPI compared with phones or monitors, often under 10. That sounds broken until you remember viewing distance. These walls are watched from metres away, where a handful of pixels per inch is plenty. Pitch is simply the more practical unit when millimetres and metres are the working scale.

Why Pitch Decides Viewing Distance

Stand too close to a coarse-pitch wall and you see individual LEDs with dark gaps between them, an effect installers call the screen-door look. Back away and the dots merge into a continuous image. The crossover distance grows with the pitch.

The industry rule of thumb is beautifully simple: the minimum comfortable viewing distance in metres is roughly equal to the pitch in millimetres. A P2.6 wall wants viewers at least 2.6 metres back; a P10 wall wants 10 metres. The calculator reports this estimate automatically.

Common Pitches and Where They Are Used

Fine pitches from P0.9 to P2.5 serve control rooms, broadcast studios, and corporate lobbies, where viewers stand a few metres away and expect monitor-like sharpness. Mid-range P2.6 to P4 covers concerts, conferences, and houses of worship with audiences at moderate distance.

Coarse pitches from P5 to P10 and beyond belong outdoors: stadium perimeters, building facades, and highway billboards viewed from tens of metres. Out there, fine pitch would be wasted money, because no viewer gets close enough to see the difference.

Indoor Versus Outdoor Cabinets

Indoor cabinets prioritise fine pitch and low brightness, since viewers are close and ambient light is controlled. Outdoor cabinets trade pitch for brightness and weatherproofing, pushing thousands of nits to stay visible in sunlight.

This is why you cannot judge a wall by pitch alone. An outdoor P6 cabinet and an indoor P6 cabinet share the same pixel spacing but differ enormously in brightness, sealing, and price. Match the cabinet type to the environment first, then choose the pitch for the viewing distance.

Cabinet Math: From One Panel to a Whole Wall

Video walls are built from standard cabinets, commonly 500 by 500 mm or 500 by 1000 mm. Once you know one cabinet’s pixel count and pitch, scaling up is multiplication. A wall ten cabinets wide and six tall, using 192-by-192-pixel cabinets, is 1920 by 1152 pixels overall.

The pitch never changes as you add cabinets, which is the beauty of the system. Calculate it once from a single cabinet and it describes a wall of any size built from the same panels. Content creators use the total pixel count to size their media; installers use the pitch to set viewing distances.

Pitch Versus Resolution

Resolution counts total pixels; pitch describes their spacing. A wall can have enormous resolution and coarse pitch at the same time: just build it big enough. A 100-metre-wide P10 facade holds 10,000 pixels across, which is massive resolution at a pitch no phone would tolerate.

When someone asks whether a wall is high resolution, ask two questions back: how many pixels total, and at what pitch. The first tells you the media server requirements; the second tells you how close the audience can stand. Both matter, and neither replaces the other.

The Cost Curve of Fine Pitch

Halving the pitch quadruples the LED count per square metre, and cost follows roughly the same curve. A P1.5 wall can cost several times more per square metre than a P3 wall of the same size, before installation.

The smart buy is the coarsest pitch your viewing distance allows. Paying for P1.2 in a venue where the nearest viewer stands 8 metres away buys invisible quality. Run the pitch through the viewing-distance rule first, then spend the savings on brightness, processing, or spare modules.

Also budget for the infrastructure that fine pitch demands. Denser walls need more powerful sending cards, more data cabling, and more careful calibration, because colour and brightness uniformity matter more when pixels are tiny. The panel price is only part of the total project cost.

Measuring Pitch on a Real Panel

If you have the panel in front of you, count the pixels across one module and measure the module width with calipers or a steel rule. Divide width by count, exactly as the formula says. Measure a few modules and average, since manufacturing tolerances add small variations.

Do not measure the whole wall and guess the pixel count from the spec sheet if you can avoid it. Spec sheets sometimes round, and a rounded width over a rounded pixel count can shift the pitch by a tenth of a millimetre. One careful cabinet measurement beats ten catalogue figures.

Common Pixel Pitch Mistakes

The most common mistake is mixing up pitch with resolution and ordering a fine-pitch wall for a long-distance application, or a coarse wall for a lobby. The second is measuring the cabinet in centimetres or inches and forgetting to convert to millimetres before dividing.

Another frequent error is counting pixels vertically instead of horizontally, or counting across two modules instead of one. Pitch is per-module spacing, so the pixel count and the width must describe the same single cabinet. Keep the pair together and the math stays honest.

A subtler mistake is ignoring the pixel layout inside each pixel. Some outdoor panels group red, green, and blue diodes with small gaps that make the effective pitch slightly larger than the simple width-over-count figure. For planning purposes the simple figure is fine, but for broadcast-critical work ask the manufacturer for the true optical pitch.

Worked Example: P2.6 Rental Cabinet

Take a standard rental cabinet: 192 pixels across, 500 mm wide. Pitch equals 500 divided by 192, which is 2.604 mm. In catalogue terms this is a P2.6 panel.

The PPI equivalent is 25.4 divided by 2.604, which is 9.75 PPI. The minimum viewing distance is about 2.6 metres. This is the workhorse of the concert and corporate event world: sharp enough for audiences a few metres back, affordable enough to fly in large quantities.

Enter 192 and 500 in the calculator to confirm 2.604 mm, 9.75 PPI, and the 2.6-metre viewing hint.

Worked Example: P3.9 Stage Wall

Now a coarser stage cabinet: 128 pixels across the same 500 mm width. Pitch equals 500 divided by 128, which is 3.906 mm, sold as P3.9.

PPI equivalent is 25.4 divided by 3.906, which is 6.50 PPI. Minimum viewing distance is about 3.9 metres. Compared with the P2.6 cabinet, this panel uses roughly half the LEDs per square metre, which shows directly in the rental price.

For an audience seated 6 metres and beyond, the P3.9 wall looks essentially identical to the P2.6 one, at a fraction of the cost. Distance is the great equaliser.

Worked Example: Wide P3.1 Panel

Consider a 1000 mm wide cabinet with 320 pixels across. Pitch equals 1000 divided by 320, which is 3.125 mm, sold as roughly P3.1.

PPI equivalent is 25.4 divided by 3.125, which is 8.13 PPI. Minimum viewing distance is about 3.1 metres. Wide cabinets like this reduce the number of panels, power supplies, and rigging points for a given wall size, which installers love.

The pitch math does not care about cabinet width: 320 pixels over 1000 mm is the same density story as 160 pixels over 500 mm. Only the ratio matters.

Worked Example: Outdoor P4 Billboard

Finally, an outdoor module: 96 pixels across a 384 mm wide module. Pitch equals 384 divided by 96, which is exactly 4.0 mm, a P4 panel.

PPI equivalent is 25.4 divided by 4.0, which is 6.35 PPI. Minimum viewing distance is about 4.0 metres, though billboard audiences are usually far farther away. At highway distance the image looks perfectly smooth.

This example shows why outdoor walls stop at coarse pitches: nobody stands 4 metres from a billboard, so finer pitch would add cost with zero visible benefit.

Frequently Asked Questions

1. What does P2.6 mean on an LED wall?

It means the pixel pitch is about 2.6 mm: the centre-to-centre distance between neighbouring pixels. Smaller numbers mean denser, sharper pixels.

2. How do I calculate pixel pitch?

Divide the cabinet width in millimetres by the horizontal pixel count: pitch = width / pixels. The calculator also converts the result to PPI.

3. What is the PPI of a P3.9 wall?

Divide 25.4 by 3.9 to get about 6.5 PPI. LED walls have very low PPI because they are viewed from metres away.

4. How far should viewers stand from an LED wall?

A common rule: at least one metre per millimetre of pitch. A P2.6 wall wants viewers 2.6 metres back or more.

5. Is a smaller pixel pitch always better?

Only up to the point your audience can see the difference. Beyond the viewing distance threshold, finer pitch just costs more.

6. Can I measure pitch from the full wall?

You can, but measuring one cabinet is more accurate. Divide its width by its pixel count and average a few modules.

7. Why are outdoor walls coarser than indoor walls?

Outdoor viewers stand far away, so fine pitch is wasted. Outdoor budgets go to brightness and weatherproofing instead.

8. Does pitch change when I add more cabinets?

No. Every cabinet shares the same pitch. Adding cabinets raises total resolution and wall size, never the density.

9. What pitch do I need for a conference room?

With viewers 3 to 5 metres away, P1.5 to P2.5 is typical. Check the one-metre-per-millimetre rule against your nearest seat.

10. How does pitch relate to resolution?

Pitch sets pixel spacing; resolution counts total pixels. A huge coarse wall can out-resolve a small fine one.

11. Should I measure in inches instead?

You can, but convert to millimetres first. The industry prices, names, and rules of thumb all assume millimetres.

12. What causes the screen-door effect?

Viewing a coarse-pitch wall from too close, so individual LEDs and the gaps between them become visible. Back away past the minimum distance.

13. Do vertical and horizontal pitch differ?

On standard panels they are identical. Specialty or creative LED products can differ, so check the datasheet.

14. How many pixels are in a 500 mm P2.6 cabinet?

Divide 500 by 2.6 to get about 192 pixels across. Real cabinets round to convenient numbers like 192 by 192.

15. Is the calculator result a product specification?

No. It is a planning estimate from your measurements. Confirm critical builds against the manufacturer’s datasheet.