Skip to content
Internet

Nas Storage Calculator

Nas Storage Calculator

See the true usable terabytes before you buy a single drive.

Four 8 TB drives do not give you 32 TB of usable space. RAID parity and the filesystem take their share first. This planner shows what is left for your files.

Whole number of identical drives you plan to install.
Advertised capacity of each drive in terabytes.
Space the filesystem keeps for metadata and safety, usually 5% to 10%.

Buying drives for a home or small-office NAS feels like simple multiplication: four 8 TB drives should give you 32 TB of space. It never works out that way. First the RAID level takes its share for parity or mirrors, then the filesystem holds back a reserve for its own metadata and safe operation. The Nas Storage Calculator walks through all three steps, raw capacity, RAID overhead, and filesystem reserve, and tells you the number that actually matters: how many terabytes you can really store. Run it before you order drives, because the gap between the box label and reality decides whether you need four drives or six.

What This Calculator Does

This is a capacity planner, not a RAID designer. You tell it how many identical drives you plan to buy, how big each drive is in terabytes, which RAID level you will run, and what percentage the filesystem should keep in reserve. It computes the total raw capacity as drives times size, applies the RAID level’s usable-space formula, subtracts the filesystem reserve, and reports the final usable storage in TB and GB, along with how much each layer cost you and your overall storage efficiency. The result answers the shopping question directly: “If I buy these drives and run this RAID level, how much room do I get for my files?” It assumes all drives are the same size, which matches how most people build a NAS.

How to Use the Calculator

Enter the number of drives as a whole number, from 1 to 64. Enter the advertised size of each drive in terabytes, for example 8 for an 8 TB drive. Choose a RAID level from the dropdown: RAID 0 for maximum space with no redundancy, RAID 1 for mirroring, RAID 5 for single parity, RAID 6 for dual parity, or RAID 10 for mirrored stripes. Enter the filesystem reserve as a percentage, typically 5 to 10; 5 is pre-filled as a sensible default. Press Calculate to see the full breakdown: raw capacity, RAID usable space, RAID overhead lost, the reserve amount, storage efficiency, and the headline usable storage figure. Use Reset to clear the form and compare another combination, such as the same drives in RAID 5 versus RAID 6.

The Formula and How It Works

The math has three layers. First, raw capacity = number of drives x drive size. Second, RAID usable space depends on the level: RAID 0 gives all of it, drives x size; RAID 1 gives one drive’s worth, just size, because the second drive is a copy; RAID 5 gives (drives – 1) x size, losing one drive to parity; RAID 6 gives (drives – 2) x size, losing two drives to parity; RAID 10 gives (drives / 2) x size, half the drives mirrored. Third, usable storage = RAID usable x (1 – reserve / 100), and storage efficiency = usable storage / raw capacity x 100. The calculator also enforces the rules each level needs: RAID 1 needs at least 2 drives, RAID 5 needs at least 3, RAID 6 needs at least 4, and RAID 10 needs at least 4 with an even count. Break a rule and it tells you exactly what is wrong instead of giving a nonsense number.

Worked Example 1: Four 8 TB Drives in RAID 5

You buy four 8 TB drives, run RAID 5, and keep a 5% filesystem reserve. Step one: raw capacity = 4 x 8 = 32.00 TB. Step two: RAID 5 usable = (4 – 1) x 8 = 24.00 TB, so parity costs you 8.00 TB. Step three: the 5% reserve on 24.00 TB is 1.20 TB, leaving 24.00 – 1.20 = 22.80 TB of usable storage, which is 23347.20 GB. Storage efficiency is 22.80 / 32.00 x 100 = 71.25%. The lesson is the gap: the boxes promised 32 TB, and your files get 22.80 TB. That is normal and healthy, one drive of parity plus a modest reserve, but it shows why you should never size a NAS from the raw number alone.

Worked Example 2: Two 4 TB Drives in RAID 1

A simple two-bay NAS with two 4 TB drives mirrored in RAID 1 and a 10% reserve. Step one: raw = 2 x 4 = 8.00 TB. Step two: RAID 1 usable = 4.00 TB, because the second drive holds a copy, so mirroring costs 4.00 TB. Step three: 10% of 4.00 TB is 0.40 TB, leaving 4.00 – 0.40 = 3.60 TB usable, which is 3686.40 GB. Efficiency is 3.60 / 8.00 x 100 = 45.00%. This is the price of simplicity and safety: you lose half your raw space to the mirror. For a two-bay home NAS holding family photos, that trade is usually worth it, but go in with open eyes about the 3.60 TB ceiling.

Worked Example 3: Six 12 TB Drives in RAID 6

A bigger build: six 12 TB drives, RAID 6 for dual parity, 7% reserve. Step one: raw = 6 x 12 = 72.00 TB. Step two: RAID 6 usable = (6 – 2) x 12 = 48.00 TB, losing 24.00 TB to the two parity drives. Step three: 7% of 48.00 TB is 3.36 TB, leaving 48.00 – 3.36 = 44.64 TB usable, or 45711.36 GB. Efficiency is 44.64 / 72.00 x 100 = 62.00%. Dual parity costs more than RAID 5, about 9 points of efficiency here, but with six large drives the rebuild window after a failure is long, and that second parity drive is cheap insurance against a second failure during the rebuild.

Worked Example 4: Four 6 TB Drives in RAID 10

Four 6 TB drives in RAID 10 with a 5% reserve, a common pick for speed plus safety. Step one: raw = 4 x 6 = 24.00 TB. Step two: RAID 10 usable = (4 / 2) x 6 = 12.00 TB, so the mirrors cost 12.00 TB. Step three: 5% of 12.00 TB is 0.60 TB, leaving 12.00 – 0.60 = 11.40 TB usable, which is 11673.60 GB. Efficiency is 11.40 / 24.00 x 100 = 47.50%. RAID 10 gives you excellent rebuild speed and can survive certain two-drive failures, but it is the hungriest option on space. Compare it with the RAID 5 example: same four drives at 6 TB in RAID 5 would give (4 – 1) x 6 x 0.95 = 17.10 TB usable instead of 11.40 TB.

Understanding Your Results

The headline number is the estimated usable storage in TB and GB, the space your files, media, and backups can actually occupy. The rows above it show where the rest went: total raw capacity is what the drive boxes add up to, the RAID usable row shows what survives parity or mirroring, the RAID overhead row quantifies the redundancy tax, the filesystem reserve row shows the safety margin, and storage efficiency rolls it all into one percentage. Use efficiency to compare plans: a higher number means more of your money turned into file space, a lower number means you paid more for protection and safety. Neither is wrong, but the number makes the trade-off visible instead of hidden in marketing.

Common Mistakes to Avoid

The most common mistake is shopping with the raw number: buying exactly enough drives to cover your data on paper, then discovering the usable figure falls short. Always size from the calculator’s usable output and add 20 to 30% headroom for growth. Second, people forget RAID minimums and parities, like planning RAID 5 on two drives or an odd drive count for RAID 10; the calculator blocks these, but your shopping list should respect them too. Third, many builders set the filesystem reserve to zero to squeeze out space, which risks fragmentation and instability when the volume fills up. Fourth, mixing drive sizes breaks the equal-size assumption: most RAID setups treat every drive as the size of the smallest one, wasting the extra. Finally, remember that RAID is not a backup; it protects against drive failure, not against deletion, ransomware, or fire, so plan an off-device backup as well.

Frequently Asked Questions

1. Why is usable storage always less than the raw total?

Because redundancy and the filesystem take their cut before your files arrive. RAID parity or mirrors reserve whole drives worth of space so the array survives failures, and the filesystem keeps a percentage for metadata and safe operation. The calculator shows each cut separately so you can see exactly where the terabytes go.

2. How is this different from a NAS RAID calculator?

A RAID calculator usually focuses on redundancy, fault tolerance, and which RAID level fits your drive count. This planner is storage-focused: it starts from your shopping list of drives and answers how many usable terabytes you get after RAID overhead and filesystem reserve are subtracted.

3. What filesystem reserve percentage should I use?

Five percent is a solid default for most home and small-office arrays, which is why the calculator pre-fills it. Use 10% if the volume will hold many small files or snapshots, which consume more metadata. Setting it to zero is not recommended because a completely full filesystem becomes slow and fragile.

4. Why does RAID 1 only give me one drive’s worth of space?

Because RAID 1 mirrors: every byte written to the first drive is copied to the second. You gain the ability to lose either drive without losing data, and the price is that the second drive adds zero usable capacity. Two 4 TB drives in RAID 1 give 4 TB usable, not 8 TB.

5. Which RAID level gives the most usable space?

RAID 0 gives 100% of raw capacity but no protection at all, so it is rarely right for a NAS. Among protected levels, RAID 5 usually gives the most usable space per dollar, losing only one drive to parity. RAID 6 loses two drives and RAID 10 loses half, in exchange for stronger protection.

6. Why does RAID 10 need an even number of drives?

RAID 10 builds mirrored pairs and then stripes across the pairs. Every drive needs a mirror partner, so an odd drive out has nothing to pair with. The calculator requires at least 4 drives and an even count, and explains the problem if you enter anything else.

7. Can I mix different drive sizes in one array?

The calculator assumes identical drives, and most RAID setups effectively do the same: they treat every drive as the size of the smallest one, so the extra space on larger drives is wasted. If you plan mixed sizes, enter the smallest drive size and the number of drives for a conservative estimate.

8. Does the reserve cover snapshots and versioning?

Not exactly. The filesystem reserve covers metadata and operational safety. Snapshots consume additional space on top of it as your data changes. If you plan heavy snapshot use, either raise the reserve or, better, budget snapshot space separately when sizing your array.

9. What does the storage efficiency percentage tell me?

It tells you what share of the raw terabytes you paid for actually becomes file space. Seventy percent means 30% went to parity and reserve. Use it to compare plans: RAID 5 at 71.25% versus RAID 10 at 47.50% makes the protection-versus-space trade-off concrete.

10. Should I include a hot spare drive in the count?

No. Enter only the drives that will hold the array. A hot spare sits idle until a failure happens and contributes no usable space, so counting it would inflate your result. Size the array with the calculator, then add the spare drive to your shopping list separately.

11. Why do drive makers’ terabytes differ from what my computer shows?

Drive makers count a terabyte as 1,000 gigabytes, while operating systems traditionally count 1,024. An 8 TB drive therefore shows about 7.28 TiB in the OS. The calculator works in the maker’s decimal terabytes, matching the box labels you shop with, and shows GB equivalents for reference.

12. Is RAID a backup for my files?

No, and this is the most important thing on this page. RAID protects against drive failure only. It does not protect against accidental deletion, ransomware, theft, or fire, all of which can take the whole array at once. Keep a separate backup on different hardware or off-site, whatever the calculator says.

13. How much headroom should I leave for growth?

A good rule is to buy for today’s data plus 20 to 30% extra, or about two years of growth. Media libraries and backups grow faster than people expect, and expanding an array later is slower and riskier than starting with room. Use the usable figure from the calculator as your starting point, not your ceiling.

14. Does the calculator account for the operating system drive?

It assumes every drive you enter belongs to the storage array. If your NAS boots from a separate drive or SSD, do not include that drive in the count. Only the drives holding your data volume belong in this calculation.

15. Can I use this for a direct-attached RAID enclosure too?

Yes. The math is identical whether the drives sit in a NAS, a USB RAID enclosure, or a server: raw capacity minus RAID overhead minus filesystem reserve equals usable space. Just make sure the RAID level you pick matches what the enclosure actually supports.

Final Thoughts

The cheapest time to fix a capacity mistake is before you buy the drives. The Nas Storage Calculator turns a hopeful guess into a planned number: raw terabytes on the boxes, minus honest RAID overhead, minus a sensible filesystem reserve, equals the space your files really get. Run your shortlist of drive counts and RAID levels through it, pick the combination whose usable figure covers your data with room to grow, and you will never be surprised by a NAS that fills up in the first month. Plan the space, then buy the drives, in that order.