Nas Raid Calculator
Enter how many drives your NAS has, the size of each drive, and the RAID level to see your usable capacity, raw capacity, and protection overhead.
Four 8 TB drives sounds like 32 TB of storage — until you set up RAID and discover you actually get 24 TB, or 16 TB, or the full 32 TB, depending on the level you choose. That gap between raw and usable capacity is the price of protecting your data against a dead drive, and it catches almost every first-time NAS buyer by surprise. The Nas Raid Calculator above removes the surprise: enter your drive count, drive size, and RAID level, and it shows the usable capacity you will actually get, the raw total, and the overhead that protection costs you.
RAID — Redundant Array of Independent Disks — spreads your data across multiple drives so that one (or two) of them can fail without losing anything. Different RAID levels make different tradeoffs between usable space, fault tolerance, and performance. This calculator covers the six levels home and small-office NAS owners actually use: RAID 0, 1, 5, 6, 10, and Synology’s SHR. Run your planned setup through it before you buy drives, and you will never end up with less space — or less protection — than you expected.
What the Nas Raid Calculator Does
The calculator answers the capacity question for your exact hardware: given N drives of S terabytes each in a given RAID level, how many terabytes can you actually store? It applies the standard capacity formula for the selected level, then reports three numbers. Raw capacity is the simple total — drives times size — with no protection subtracted. Usable capacity is what the file system gives you after the RAID level reserves its redundancy. Protection overhead is the difference: the terabytes “spent” on surviving drive failures.
It also enforces the rules each level requires. Every level needs a minimum number of drives — RAID 5 needs at least 3, RAID 6 and RAID 10 need at least 4 — and RAID 10 needs an even count because it builds mirrored pairs. If your setup breaks a rule, the calculator tells you exactly which rule and why, instead of giving a misleading number.
How to Use the Calculator
Enter the number of drives in your NAS — most home units take 2, 4, 5, 6, or 8. Then enter the size of each drive in terabytes, such as 8 for 8 TB drives. The calculator assumes all drives are the same size, which is the recommended setup; if you mix sizes, most RAID levels only use the smallest drive’s capacity on every disk, so enter the smallest size for a safe estimate. Then pick your RAID level from the dropdown.
Click Calculate to see the RAID level, raw capacity, usable capacity, and protection overhead. Invalid setups — fewer than 2 drives, a zero drive size, too few drives for the chosen level, or an odd drive count for RAID 10 — produce a specific error message explaining the requirement. The Reset button clears the form. A smart workflow is to run two or three RAID levels for the same drives and compare: the overhead column shows exactly what each extra level of protection costs in terabytes.
How the Math Works
Each RAID level has one simple capacity formula, where n is the drive count and s is the drive size in TB. RAID 0 stripes data with no redundancy: usable = n × s. RAID 1 mirrors everything: usable = s, no matter how many drives you add. RAID 5 spreads one drive’s worth of parity across the array: usable = (n − 1) × s, surviving one drive failure. RAID 6 uses double parity: usable = (n − 2) × s, surviving two failures. RAID 10 mirrors pairs and then stripes across them: usable = (n / 2) × s, needing an even n of at least 4. SHR with one-disk fault tolerance behaves like RAID 5 for equal-size drives: usable = (n − 1) × s.
Raw capacity is always n × s, and protection overhead is simply raw minus usable. These formulas give decimal terabytes (1 TB = 1,000 GB as drive makers define it); your operating system will report slightly less because it counts in tebibytes, so expect the NAS itself to show a number a few percent lower than the calculator’s usable figure.
Worked Examples
Five setups, each computed step by step with the calculator’s exact formulas.
Example 1 — four 8 TB drives in RAID 5. Raw = 4 × 8 = 32.00 TB. RAID 5 reserves one drive’s worth of parity: usable = (4 − 1) × 8 = 3 × 8 = 24.00 TB. Overhead = 32.00 − 24.00 = 8.00 TB. This is the classic home-NAS sweet spot: you lose one drive of space and can survive any single drive dying.
Example 2 — six 10 TB drives in RAID 6. Raw = 6 × 10 = 60.00 TB. RAID 6 reserves two drives of parity: usable = (6 − 2) × 10 = 4 × 10 = 40.00 TB. Overhead = 60.00 − 40.00 = 20.00 TB. Double parity costs more space, but the array survives two simultaneous failures — the safer choice for large drives that take days to rebuild.
Example 3 — four 12 TB drives in RAID 10. Raw = 4 × 12 = 48.00 TB. RAID 10 mirrors pairs: usable = (4 / 2) × 12 = 2 × 12 = 24.00 TB. Overhead = 48.00 − 24.00 = 24.00 TB. You sacrifice half your space, but you get the best performance and the fastest rebuilds of any redundant level.
Example 4 — two 6 TB drives in RAID 1. Raw = 2 × 6 = 12.00 TB. Mirroring keeps one exact copy: usable = 6.00 TB. Overhead = 12.00 − 6.00 = 6.00 TB. Simple, and the standard choice for a 2-bay NAS where losing half your space is the price of sleeping well.
Example 5 — three 4 TB drives in SHR. Raw = 3 × 4 = 12.00 TB. SHR with one-disk tolerance works like RAID 5 on equal drives: usable = (3 − 1) × 4 = 8.00 TB. Overhead = 12.00 − 8.00 = 4.00 TB. And for contrast, the same three drives in RAID 0 would give the full 12.00 TB usable with zero overhead — and zero protection, since any single failure destroys everything.
Understanding Your Results
Usable capacity is the number to plan around: it is the space your shared folders, backups, and media libraries actually get. Compare it against what you need today plus growth — a good rule is to buy for about twice your current data if you plan to keep the NAS for several years. Raw capacity tells you what you paid for in total; the gap between raw and usable, shown as protection overhead, is the insurance premium in terabytes.
The RAID level line confirms the tradeoff you chose. More overhead means more failures survived and usually slower writes; less overhead means more space but thinner protection. If the overhead shocks you, that is useful information — it means you were about to buy the wrong combination of drives and level, and a cheaper set of larger drives or a different level would serve you better.
Common Mistakes to Avoid
The number-one mistake is buying drives for the raw total — “four 8 TB drives is 32 TB” — and then being angry at RAID 5 for “eating” 8 TB. It did not eat anything; the parity was always part of the deal. The second mistake is picking RAID 0 for irreplaceable data like family photos: it is fast and gives full capacity, but one dead drive means total loss, which is the opposite of what a NAS is for.
Other frequent errors: mixing drive sizes and expecting full use of the big ones (most levels cap every drive at the smallest size); choosing RAID 5 with very large drives, where a multi-day rebuild stresses the remaining drives and a second failure during rebuild kills the array — RAID 6 is the safer pick above 8–10 TB per drive; and forgetting that RAID is not a backup. RAID keeps you running through a drive failure, but it does not protect against theft, fire, ransomware, or accidental deletion. Keep an off-site or external backup no matter which level you choose.
Frequently Asked Questions
1. What is the difference between raw and usable capacity?
Raw capacity is drives × size with nothing subtracted. Usable capacity is what remains after the RAID level reserves space for redundancy. The difference is the protection overhead shown by the calculator.
2. Which RAID level should a home user choose?
RAID 5 or SHR for 3+ bays is the most popular home choice: one drive of overhead and survival of any single failure. Use RAID 1 for a 2-bay NAS, and RAID 6 if your drives are very large or your data is critical.
3. Why does RAID 5 need at least 3 drives?
Its parity scheme needs at least two data stripes plus parity distributed across the array. With only 2 drives and one drive of parity, you would be left with a single drive of usable space — that is just mirroring, which is RAID 1’s job.
4. Why does RAID 10 need an even number of drives?
RAID 10 builds mirrored pairs first, then stripes across the pairs. An odd drive out cannot be paired, so the level requires an even count — 4, 6, or 8 drives.
5. What is SHR?
Synology Hybrid RAID, an automated RAID management system on Synology NAS units. With one-disk fault tolerance and equal-size drives it gives the same usable capacity as RAID 5, but it handles mixed drive sizes more flexibly.
6. Is RAID a backup?
No. RAID protects against drive failure so the NAS keeps running, but it does not protect against deletion, ransomware, fire, or theft. Every NAS owner should also keep a real backup, ideally off-site.
7. Why does my NAS show less space than the calculator?
Drive makers define 1 TB as 1,000 GB, while operating systems count in tebibytes (1 TiB = 1,024 GiB), which reads about 9% lower. The file system and NAS software also reserve a little space. Expect the NAS to show a few percent less than the calculator’s figure.
8. Can I mix different drive sizes?
You can, but traditional RAID levels use only the smallest drive’s capacity on every disk, wasting the extra space on larger drives. SHR handles mixed sizes better. For a clean estimate, enter your smallest drive size in the calculator.
9. What happens when a drive fails in RAID 5?
The array keeps working in a degraded state using the parity data. You replace the dead drive, and the NAS rebuilds the missing data onto the new drive — a process that can take many hours on large drives, during which a second failure would destroy the array.
10. Should I use RAID 5 or RAID 6 with 12 TB drives?
RAID 6. Rebuilding a 12 TB drive takes a long time and stresses the surviving drives, which raises the chance of a second failure mid-rebuild. RAID 6 survives that second failure; RAID 5 does not.
11. Does RAID 0 have any place in a NAS?
Only for data you can afford to lose completely — scratch space, caches, or temporary media transcoding. For anything irreplaceable, RAID 0’s zero fault tolerance makes it the wrong choice.
12. How many drives can fail in RAID 10?
At least one, and possibly more if the failures land in different mirrored pairs. If both drives of the same pair fail, the array is lost. It is tougher than RAID 5 against scattered failures but weaker than RAID 6 against two unlucky ones.
13. Can I change RAID level later without losing data?
Many NAS systems, including Synology’s, support migrating from RAID 1 to RAID 5 or SHR, or adding drives to expand, without data loss. Downgrading or shrinking usually requires a backup, wipe, and restore — check your NAS maker’s migration matrix first.
14. Do I need NAS-specific drives?
They are strongly recommended. NAS-rated drives are built for 24/7 operation, vibration from neighboring drives, and RAID error recovery behavior. Desktop drives can drop out of arrays under sustained NAS workloads.
15. How much free space should I leave on the NAS?
Keep at least 10–20% of usable capacity free. Full volumes fragment, slow down, and can prevent snapshots and rebuild operations from working properly. Size your drives with the calculator so your data lands well under the usable figure.
Final Thoughts
The Nas Raid Calculator turns NAS shopping from guesswork into arithmetic. Pick your drives, pick your RAID level, and you instantly see the usable capacity you will live with, the raw total you paid for, and the overhead your protection costs. The examples show the real tradeoffs: RAID 5’s single-drive tax, RAID 6’s double insurance, RAID 10’s 50% sacrifice for speed, and RAID 1’s simple mirror. Plan with the usable number, leave headroom for growth, choose the level that matches how much your data matters — and remember that RAID keeps you running, but only a real backup keeps you safe.