Gearing Calculator
Bicycle gearing made simple — enter your chainring, cog, wheel size, and cadence to get gear ratio, gear inches, and speed.
Every cyclist has felt it: that perfect gear where your legs spin effortlessly and the bike just flies, and that awful gear where your knees scream on a hill or your legs spin uselessly on a descent. The difference is gearing, and the Gearing Calculator turns it from guesswork into numbers. Enter your chainring teeth, rear cog teeth, wheel diameter, and pedaling cadence, and it instantly tells you your gear ratio, your gear inches, and the speed you will travel at that cadence. Whether you are choosing a cassette for a hilly ride or comparing two bikes, these three numbers tell you everything.
Gearing is the mechanical language of your bicycle. It decides how far the bike travels with each turn of the pedals, how hard each pedal stroke feels, and how fast you can go at a comfortable cadence. A single-speed rider picks one gear for everything; a road cyclist with 22 gears has a whole toolbox. This calculator works for all of them — just enter the combination you are curious about, one at a time, and compare the results. In a few clicks you will understand your drivetrain better than most riders ever do.
What This Calculator Does
The Gearing Calculator computes three classic cycling measurements from your drivetrain. First, the gear ratio: chainring teeth divided by rear cog teeth. A 50-tooth chainring with a 17-tooth cog gives 50 ÷ 17 = 2.94, meaning the rear wheel turns 2.94 times for each full turn of the cranks. Second, gear inches: the gear ratio multiplied by the wheel diameter in inches. This is the traditional way cyclists compare gears across different wheel sizes — a bigger wheel covers more ground per turn, so gear inches capture the real “size” of the gear. Third, your speed in miles per hour at your chosen cadence, calculated from how far the wheel rolls per crank revolution.
Why three numbers instead of one? Because each answers a different question. Gear ratio tells you the mechanical advantage — how the drivetrain multiplies your effort. Gear inches lets you compare gears fairly between bikes with different wheel sizes, which is why it has survived more than a century of cycling. Speed at cadence answers the practical question: if I pedal at 90 rpm in this gear, how fast am I actually going? Together they give you the complete picture of what a gear combination really means on the road.
How to Use the Gearing Calculator
Start with your chainring teeth — the number stamped on the front ring you are using (count them if you are not sure). Then enter the rear cog teeth for the sprocket you want to analyze. Enter your wheel diameter in inches, measured across the outside of the tire — a typical road wheel is about 27 inches, a 700c wheel with tires is roughly 27 to 28 inches, and a 26-inch mountain bike wheel is about 26 inches. Finally, enter your cadence in revolutions per minute; 90 is already filled in because it is the comfortable cruising cadence most coaches recommend.
Press Calculate and you will see the gear ratio, gear inches, and speed at your cadence. To compare gears, change just the cog teeth and calculate again — everything else stays the same, so the difference in the numbers is purely the effect of that cog. To compare bikes, keep the chainring and cog the same but change the wheel diameter. Press Reset to clear everything and start fresh.
The Formulas and What Each Part Means
Three simple formulas power the calculator. Gear ratio = chainring teeth ÷ rear cog teeth. This is pure drivetrain math: a bigger front ring or a smaller rear cog raises the ratio, meaning more wheel turns per pedal turn. Gear inches = gear ratio × wheel diameter in inches. This dates back to the days of penny-farthing bicycles, where the gear was literally the diameter of the driven wheel — a 79-inch gear today feels like riding a penny-farthing with a 79-inch front wheel.
Speed comes from the distance the wheel rolls. One wheel revolution covers π × wheel diameter inches. In one minute at your cadence, the wheel turns gear ratio × cadence times, so the bike covers gear inches × π × cadence inches per minute. Multiply by 60 for inches per hour, then divide by 63,360 (the number of inches in a mile) to get miles per hour. The full formula: speed (mph) = gear inches × π × cadence × 60 ÷ 63,360. Every step follows directly from the geometry of the wheel — no approximations, just arithmetic.
Worked Example 1: 50×17 at 90 RPM on 27-Inch Wheels
Take a classic road setup: a 50-tooth chainring, a 17-tooth cog, 27-inch wheels, and a 90 rpm cadence. First the gear ratio: 50 ÷ 17 = 2.9412, which the calculator shows as 2.94. Next, gear inches: 2.9412 × 27 = 79.41, shown as 79.4 inches. Now the speed: 79.4118 × π = 249.48 inches per wheel-revolution-equivalent; times 90 rpm gives 22,453.6 inches per minute; times 60 gives 1,347,216 inches per hour; divided by 63,360 inches per mile gives 21.26 mph, shown as 21.3 mph. So at a comfortable 90 rpm spin, this gear cruises at just over 21 mph — a typical fast flat-road gear.
Worked Example 2: 44×16 at 90 RPM on 27-Inch Wheels
Now a slightly easier gear: 44-tooth chainring, 16-tooth cog, same 27-inch wheels and 90 rpm. Gear ratio: 44 ÷ 16 = 2.75 exactly. Gear inches: 2.75 × 27 = 74.25, shown as 74.3 inches. Speed: 74.25 × π = 233.28; × 90 = 20,995.5 inches per minute; × 60 = 1,259,730 inches per hour; ÷ 63,360 = 19.88 mph, shown as 19.9 mph. Compare with the first example: dropping from a 50×17 to a 44×16 costs about 1.4 mph at the same cadence, but each pedal stroke feels noticeably lighter — exactly the trade you want when the road tilts upward.
Worked Example 3: 52×11 at 95 RPM on 27-Inch Wheels
Finally, a big sprinting gear: 52-tooth chainring, 11-tooth cog, 27-inch wheels, spinning at 95 rpm. Gear ratio: 52 ÷ 11 = 4.7273, shown as 4.73. Gear inches: 4.7273 × 27 = 127.64, shown as 127.6 inches — a huge gear. Speed: 127.6364 × π = 401.00; × 95 = 38,095.2 inches per minute; × 60 = 2,285,712 inches per hour; ÷ 63,360 = 36.08 mph, shown as 36.1 mph. This is the gear sprinters use in the final 200 meters of a race: at 95 rpm it carries you past 36 mph, but pushing it requires serious leg strength.
How to Read Your Results
The gear ratio tells you the mechanical story. Ratios near 1.0 (or below, like a 34×32 climbing gear at 1.06) are easy gears: the wheel barely turns per pedal stroke, so hills feel manageable. Ratios around 2.5 to 3.0 are everyday cruising gears. Ratios above 4.0 are hard, fast gears for descents and sprints. If your ratio looks surprisingly high or low, double-check that you entered the chainring and cog in the right boxes — swapping them is the most common error.
Gear inches are your comparison tool. Because they include wheel size, you can fairly compare a gear on a 26-inch mountain bike with one on a 27-inch road bike — something gear ratio alone cannot do. As a rough guide: under 40 inches is a granny climbing gear, 40 to 60 is for serious hills, 60 to 80 covers normal riding, 80 to 100 is fast flat cruising, and over 100 is for descents and sprints. The speed figure ties it to your legs: it shows what that gear means at your actual cadence, so a 90 rpm spinner and a 75 rpm grinder can each see their own real-world speed.
Common Mistakes to Avoid
The classic mistake is entering the wheel size wrong. People enter the rim size (like 700c or 26 inches) instead of the outside diameter of the tire, or they forget that a fat tire adds diameter. Measure across the inflated tire or look up your tire’s actual outside diameter — a couple of inches of error here shifts every result. The second classic mistake is swapping chainring and cog, which produces a tiny ratio like 0.34 instead of 2.94 — if your ratio is below 1.0 on a road bike, you almost certainly swapped them.
The third mistake is using an unrealistic cadence. Beginners often enter 60 rpm because that is what they actually pedal, then wonder why the speed looks low — the speed is honest; the cadence is the thing to work on. Most coaches suggest training toward 85 to 95 rpm because it is kinder to your knees. Finally, remember the calculator assumes a perfect world: no wind, no hills, no tire slip, and no drivetrain friction. Real speed on the road will be a little lower, especially into a headwind — but for comparing gears, the relative differences are exactly right.
Frequently Asked Questions
1. What is a good gear ratio for a beginner?
Beginners do best with easy gears in the 1.5 to 2.5 ratio range, which let you spin comfortably without straining your knees. A compact crankset (50/34) paired with a wide cassette (11-32) gives you ratios from about 1.06 up to 4.55, covering everything from steep hills to fast descents. As your fitness improves, you will naturally spend more time in the harder gears.
2. What are gear inches, in plain words?
Gear inches describe how big your gear “feels,” combining your chainring, cog, and wheel size into one number. The name comes from penny-farthing bicycles, where the gear was the actual diameter of the big front wheel. A 79-inch gear today feels like pedaling a penny-farthing with a 79-inch wheel — one that no human could actually straddle, which shows how much gearing multiplies your effort.
3. How do I count teeth on my chainring and cog?
Mark one tooth with a small piece of tape or a marker, then count around until you return to the mark. Most chainrings also have the tooth count stamped on them — look for a number like “50T” on the ring itself. Cassettes often have the count stamped on each sprocket, or check the model number printed on the largest cog and look it up.
4. What cadence should I aim for?
Most cycling coaches recommend 85 to 95 rpm for steady riding — it balances efficiency with kindness to your knees. Beginners often pedal at 60 to 70 rpm, pushing hard gears slowly, which is tiring and hard on joints. Try shifting to an easier gear and spinning faster; it feels strange for a week, then becomes natural, and your endurance will improve.
5. Why does the calculator ask for wheel diameter instead of wheel size?
Because what matters is how far the wheel rolls per turn, which depends on the outside of the tire, not the rim. A “26-inch” mountain bike wheel with a fat tire can measure over 27 inches across, while a 700c road wheel with skinny tires measures about 27 inches. Using the true outside diameter keeps the gear-inches and speed math honest.
6. Can I compare two different bikes with this calculator?
Yes — that is exactly what gear inches are for. Enter each bike’s chainring, cog, and wheel diameter, and compare the gear-inches numbers directly. A 70-inch gear feels the same on a mountain bike and a road bike, even though the gear ratios differ. Just use the same cadence for both so the speed comparison is fair.
7. What gear do I need for steep hills?
For steep climbs, look for gear inches under 40 — for example, a 34-tooth chainring with a 32-tooth cog on 27-inch wheels gives about 28.7 inches. At 70 rpm that is roughly 6 mph, slow but sustainable on a hard gradient. If your easiest gear is over 50 inches and you live somewhere hilly, a wider-range cassette is one of the best upgrades you can buy.
8. Does a bigger chainring always make me faster?
No — it only makes you faster if your legs can push it at a good cadence. A huge gear at 50 rpm is slower, and far more exhausting, than a moderate gear at 90 rpm. Speed comes from power, which is force times cadence. The right gear is the biggest one you can spin smoothly at 85-plus rpm, not the biggest one you own.
9. What is the difference between gear ratio and gear inches?
Gear ratio describes only the drivetrain — chainring teeth divided by cog teeth — and ignores the wheel. Gear inches multiply the ratio by the wheel diameter, so they describe the whole system. Two bikes can share a 2.94 ratio but have different gear inches if their wheels differ, and the one with bigger wheels will go faster at the same cadence.
10. How accurate is the speed estimate?
The math itself is exact — it is pure wheel geometry. But it assumes ideal conditions: no wind, flat ground, no tire slip, and a perfectly round wheel. In the real world, air resistance is the big one: at 20 mph, most of your effort fights the wind, not the gearing. Treat the speed as the theoretical speed of the gear, perfect for comparing gears, and expect real road speed to be a bit lower.
11. My bike has two chainrings. Which one do I enter?
Enter the one you are actually using, then run the calculator again for the other one to see the full range. For example, a 50/34 crankset with an 11-28 cassette gives you everything from a 34×28 climbing gear (about 32.8 gear inches) to a 50×11 sprinting gear (about 122.7 gear inches). Comparing the two extremes shows why two chainrings are so versatile.
12. What does a gear ratio below 1.0 mean?
It means the rear wheel turns less than once per crank revolution — a very easy gear, typical of mountain bike granny gears, like 22×32 = 0.69. On a road bike, a ratio below 1.0 usually means you swapped the chainring and cog by mistake, so double-check your entries. True sub-1.0 gears exist, but they are for the steepest off-road climbs.
13. Should I change my cassette or my chainring?
Use the calculator to decide. If you only need easier gears for hills, a wider cassette (bigger largest cog) is cheaper and simpler. If you need both easier climbing and harder sprinting gears, or your current jumps between gears feel too big, a different chainring setup may help. Run your current combination and the candidate combination through the calculator and compare the gear-inches ranges.
14. Why 63,360 in the speed formula?
That is the number of inches in a mile: 5,280 feet per mile times 12 inches per foot equals 63,360. The calculator first figures out how many inches your bike travels per hour (gear inches × π × cadence × 60), then divides by 63,360 to convert inches per hour into miles per hour. It is just a unit conversion, not a fudge factor.
15. Does this calculator save my bike’s details?
No. The math runs instantly on the page when you press Calculate, and nothing you enter is sent anywhere or stored. Close or refresh the page and your numbers are gone. If you want to keep a record of your favorite gear combinations, jot down the gear-inches numbers — they are the handiest summary of a gear.
Final Thoughts
Gearing is one of those things that seems mysterious until you see the numbers, and then it becomes obvious. A 50×17 at 90 rpm is 21.3 mph; a 44×16 is 19.9 mph; the difference is one cog and a little less strain on your knees. Use the Gearing Calculator whenever you are choosing a cassette, comparing bikes, or just wondering what that gear you love is actually doing. The best gear is not the biggest one — it is the one that lets you spin smoothly, climb happily, and ride farther than you did last month.