Fence Square Footage Calculator
Find your fence’s total square footage for stain, paint, and material orders — plus how many gallons you need.
Total area: 0 sq ft
Coverage assumes about 150 sq ft per gallon on typical wood. Rough, weathered, or thirsty wood may need extra.
Nothing stalls a weekend fence project like running out of stain halfway down the back run. Guessing how much finish to buy usually ends one of two ways: a panicked mid-project trip to the store, or a garage shelf full of half-used cans you will never open again. This fence square footage calculator removes the guesswork with pure area math: enter your fence dimensions, and it tells you the total square footage plus exactly how many gallons of stain to buy.
This tool answers a different question than a cost estimator. It does not price your fence installation; it measures your fence surface so you can order the right amount of finishing material. Whether you are staining a new wood fence, repainting an old one, or ordering sealant, the square footage is the number every product label asks for.
What This Calculator Does
This calculator computes the total paintable or stainable surface area of a fence from three inputs: the fence length in feet, the fence height in feet, and whether you plan to finish one side or both sides. From the total area it estimates the gallons of stain you need, using a typical coverage rate of 150 square feet per gallon.
The result shows four things: the total area in square feet, the exact gallons of coverage your fence requires, the whole gallons you should actually buy (rounded up, since stores do not sell fractions of a gallon), and the arithmetic behind the answer so you can check it yourself.
Because it is pure geometry, the same math works for stain, paint, sealant, or primer. Just swap in the coverage rate from your product’s label if it differs from 150 square feet per gallon, and divide your total area by that number.
How to Use This Calculator
Enter the total length of the fence you plan to finish, in feet. Measure each straight run with a tape and add the runs together. Next, enter the fence height, typically 4, 6, or 8 feet. Then choose whether you are finishing one side or both sides of the fence. Press the Calculate button and your area and gallon estimates appear below the form.
Choose “Both sides” when you are responsible for the whole fence, which is the usual case for a fence that sits fully inside your property. Choose “One side” when a neighbor is handling their side, or when you are only refinishing the street-facing or interior face.
If you enter a missing or impossible value, such as a zero length, the calculator shows a clear error message instead of a nonsense answer. Use the Reset button to clear the form and run a new scenario, for example comparing one coat versus two coats by doubling the area yourself.
The Area Formula
The geometry is refreshingly simple. A fence run is a rectangle, and the area of a rectangle is length times height. Multiply by the number of sides you plan to finish, and you have the total surface area: total square feet = length x height x sides.
The stain estimate adds one more step. Product labels state coverage as square feet per gallon, and 150 square feet per gallon is a common figure for exterior wood stain. Gallons needed = total square feet / 150. Because you cannot buy 3.4 gallons, the practical answer rounds up to the next whole gallon: gallons to buy = round up(gallons needed).
That rounding-up step matters more than it looks. Buying the exact decimal amount would leave the last stretch of fence unfinished. The calculator shows you both numbers, the exact figure and the rounded-up purchase quantity, so you understand what the rounding costs you: never more than one extra gallon.
One honest limitation: this formula treats the fence as flat. It does not add extra area for the edges of pickets, the faces of posts, or decorative lattice. For most standard privacy fences the difference is small, and the round-up to whole gallons usually absorbs it.
Worked Examples With Full Arithmetic
Here are three complete examples with every step shown, so you can follow the math by hand and trust the calculator’s answers.
Example one: a 100-foot fence, 6 feet tall, finishing both sides. Step one, the area of one side: 100 x 6 = 600 square feet. Step two, both sides: 600 x 2 = 1,200 square feet. Step three, exact stain: 1,200 / 150 = 8.0 gallons. Step four, gallons to buy: round up(8.0) = 8 gallons. Answer: 1,200 sq ft, buy 8 gallons.
Example two: an 85-foot fence, 6 feet tall, finishing one side only. Step one, the area: 85 x 6 = 510 square feet. There is no doubling because only one side is being finished. Step two, exact stain: 510 / 150 = 3.4 gallons. Step three, gallons to buy: round up(3.4) = 4 gallons. Answer: 510 sq ft, buy 4 gallons. Notice how the rounding adds 0.6 gallons of safety margin here, which is welcome on real wood.
Example three: a 150-foot fence, 5 feet tall, finishing both sides. Step one, one side: 150 x 5 = 750 square feet. Step two, both sides: 750 x 2 = 1,500 square feet. Step three, exact stain: 1,500 / 150 = 10.0 gallons. Step four, gallons to buy: round up(10.0) = 10 gallons. Answer: 1,500 sq ft, buy 10 gallons.
Compare examples one and three: the second fence is longer but shorter, and the math handles the trade-off automatically. That is the whole point of the tool: no matter how your dimensions combine, the area and the gallons follow from the same two formulas.
Reading Your Results
The headline number is the total area in square feet. This is the figure to carry into the store or to type into an online order form. If a product label says it covers 200 square feet per gallon instead of 150, divide your total area by 200 yourself to adapt the estimate.
The “exact” gallons row tells you the theoretical minimum: total area divided by 150, shown to one decimal place. The “gallons to buy” row rounds that figure up to the next whole number, which is what you actually put in the cart. The “math” row shows the division in one line so you can verify it with any calculator.
Think of the exact figure as the chemistry and the rounded figure as the shopping. The gap between them is your built-in safety margin. On smooth, previously finished wood you will have finish left over; on rough or weathered wood you will be glad it is there.
Planning Stain and Paint for a Fence
Most exterior stains recommend two coats for the best protection, and two coats means twice the area. The simplest approach: run the calculator once, then double the gallons to buy. For example, the 1,200 square foot fence in example one needs 8 gallons per coat, so budget 16 gallons for two coats.
Wood condition changes everything. New, smooth cedar drinks less stain than the label suggests, while old, gray, weathered boards can absorb 20 to 30 percent more. If your fence has not been finished in years and feels rough to the touch, add one extra gallon beyond the calculator’s answer as insurance.
Do not forget the parts the flat math skips. Posts have four faces each, picket edges add up over a long run, and the bottoms of boards near the soil soak up extra finish. The round-up to whole gallons covers a little of this, but for a fence with heavy posts or a lattice top, consider adding 5 to 10 percent to the total area before dividing.
Buy all your finish at once, and if you need more than a few gallons, mix the cans together before you start. Stain color can vary slightly between batches, and boxing the cans together keeps the whole fence one consistent shade. An unopened extra gallon is easy to return; a visible color break halfway down the run is not.
Common Mistakes in Fence Area Math
The classic mistake is measuring the perimeter of the yard instead of the fence. If the fence ties into your house on two sides, those house sections are not fence. Measure the fence runs themselves, not the property boundary.
The second classic is forgetting the second side. People compute length times height, buy that many gallons, and then discover the back of the fence still needs doing. If you are finishing both faces, the area doubles, and so does the stain. The sides selector exists precisely to prevent this error.
A subtler mistake is using the nominal height instead of the finished height. A “6-foot” fence with the boards starting a few inches off the ground and a cap board on top may actually expose 6 feet 4 inches of surface. It is a small difference, but over 150 feet it adds real square footage.
Finally, people forget the second coat in their shopping math. Product coverage figures are per coat. If the label promises 150 square feet per gallon and you plan two coats, your 1,200 square foot fence needs 16 gallons, not 8. Decide your coat count before you shop, not after the first coat is dry.
Frequently Asked Questions
1. How many square feet are in a typical backyard fence?
A common suburban backyard fence runs about 100 to 150 feet long and 6 feet tall. One side of a 120-foot, 6-foot fence is 720 square feet, and both sides total 1,440 square feet. Use the calculator with your own measurements for an exact figure.
2. How many gallons of stain do I need for my fence?
Divide your total square footage by the coverage rate on the product label, often around 150 square feet per gallon, then round up. A 1,200 square foot fence needs 8 gallons per coat at that coverage rate. The calculator does this division and rounding for you.
3. Should I calculate one side or both sides of the fence?
Calculate both sides if you are finishing the entire fence, which is the usual case when it sits inside your property. Use one side only when a neighbor is handling the other face or you are refinishing a single face of the fence.
4. Why round up instead of buying the exact gallons?
Stores sell whole gallons, and running short mid-project is far worse than having a little left over. Rounding up guarantees you can finish the job, and the leftover becomes your touch-up supply for scratches and weather wear in the coming years.
5. Does the calculator account for two coats?
It calculates one coat. For two coats, simply double the “gallons to buy” figure. Most exterior stains perform best with two coats, so plan your shopping around the doubled number from the start.
6. What if my stain covers 200 square feet per gallon instead of 150?
Take the total area from the calculator and divide it by your product’s coverage rate. A 1,200 square foot fence at 200 square feet per gallon needs exactly 6 gallons per coat. Always trust the label on your specific product over any generic rate.
7. Do I need extra stain for rough or weathered wood?
Yes. Rough, dry, or long-unfinished wood can absorb 20 to 30 percent more finish than smooth wood. Add an extra gallon or two beyond the calculator’s answer for thirsty wood, especially on the first maintenance coat after years of neglect.
8. How do I measure my fence length?
Measure each straight run of fence with a tape measure and add the runs together. Do not use the property boundary unless the fence follows it exactly, and subtract any sections where the fence ties into the house or garage.
9. Does paint cover differently than stain?
Yes. Exterior paint often covers 250 to 400 square feet per gallon because it forms a film on the surface, while stain soaks in. The calculator’s area figure works for both; just divide by your paint’s labeled coverage instead of 150.
10. Should I include the posts in the square footage?
The calculator treats the fence as a flat surface and does not add post faces separately. For standard fences the round-up to whole gallons usually covers the posts. For chunky posts or a lot of them, add about 5 to 10 percent to your area before dividing.
11. How does fence height affect the gallons needed?
Directly and proportionally: area equals length times height, so an 8-foot fence needs one-third more finish than a 6-foot fence of the same length. Measure the actual finished height, including any cap boards, for the most accurate number.
12. Can I use this for a deck or pergola?
The math is the same for any flat surface: length times width gives the area, and dividing by coverage gives gallons. For a deck, enter the deck’s length and width and choose one side. Railings and balusters add fiddly extra area, so add 10 to 15 percent for those.
13. What is the difference between this and a fence cost estimator?
This calculator measures surface area for ordering finish materials like stain and paint. A fence cost estimator prices the installation itself: materials, labor, posts, and gates per linear foot. Use this tool when you are shopping for finish, and a cost estimator when you are budgeting the build.
14. How should I store leftover stain?
Seal the can tightly, store it in a cool dry place above freezing, and label it with the fence section and date. Properly stored stain keeps for several years and is perfect for touching up scratches, new boards, and sun-faded spots.
15. Is it cheaper to spray or brush stain on a fence?
Spraying is faster but uses 10 to 20 percent more product through overspray, and you must mask everything nearby. Brushing is slower but wastes almost nothing and pushes stain deeper into the wood. For most homeowners, brushing a fence is the economical choice.
Final Thoughts
Ordering the right amount of finish is a small decision that prevents a big headache. With your fence length, height, and sides, this fence square footage calculator hands you the total area and the gallons to buy in seconds, with the arithmetic shown so you can trust it. Measure carefully, remember the second coat, buy a little extra for thirsty wood, and your staining weekend will end with a beautiful fence instead of an emergency store run.