Skip to content
Construction

Cantilever Beam Calculator

Cantilever Beam Calculator

Point load at the free end: bending moment, deflection, stress, and section properties.

ft
lbs
in
in

A diving board, a balcony, a shelf bracket, an aircraft wing — all of these are cantilever beams: structural members fixed firmly at one end and free at the other. Because nothing supports the free end, a cantilever feels every bit of the load you put on it, and the forces concentrate at the fixed wall in a way that surprises many first-time builders. This Cantilever Beam Calculator analyzes the classic case of a single point load hanging at the free end of a rectangular beam. Enter the beam length, the load, the cross-section width and depth, and the material, and it returns the maximum bending moment, the maximum deflection at the free end, the bending stress, the shear force, and the key section properties — everything a student, DIY builder, or designer needs for a first-pass check.

What This Calculator Does

The Cantilever Beam Calculator solves the engineering problem of a cantilever beam with a point load P applied at its free end, assuming a rectangular cross-section and a homogeneous material. From your five inputs it computes six results. The maximum bending moment (P times L) occurs at the fixed wall and tells you how hard the beam is being twisted at its support. The maximum deflection happens at the free end and tells you how far the tip sags under load. The bending stress, found by dividing the moment by the section modulus, tells you how intensely the material fibers are being stretched and compressed. The shear force equals the full load P, constant along the beam. Finally it reports the moment of inertia and section modulus of your cross-section, the two geometric properties that control stiffness and strength. All of this follows small-deflection beam theory, the standard first-order model taught in mechanics of materials.

What Makes a Cantilever Different

A cantilever is the most demanding common beam arrangement. A simply supported beam shares its load between two supports, but a cantilever’s single fixed support must resist the entire moment alone — and that moment grows directly with length. Double the length and you double the bending moment; the deflection grows even faster, with the cube of the length. This is why diving boards are short and thick, and why balconies need such beefy connections to the building. The fixed end must be genuinely fixed: a beam merely resting on a wall is not a cantilever, and treating it as one gives dangerously wrong answers. Real cantilevers need moment-resisting connections — through-bolts, welded plates, or deep embedment — because the wall sees the full P times L moment trying to rotate the beam out of its socket. The calculator assumes a perfectly rigid wall, which is the correct idealization for sizing the beam itself.

How to Use the Cantilever Beam Calculator

Enter the beam length in feet — the distance from the wall to the point where the load hangs. Enter the point load in pounds, the total weight acting downward at the free end. Enter the cross-section width and depth in inches; for a standard 2×8 the actual dimensions are about 1.5 by 7.25 inches, and the calculator expects those real numbers, not the nominal lumber name. Choose the material from the dropdown: wood (Douglas fir at 1,900,000 psi), aluminum (10,000,000 psi), or structural steel (29,000,000 psi). Press Calculate and the result box shows all six values. If any input is missing or zero — a blank length, a negative depth — a red error box tells you exactly which field to fix, and the results stay hidden until everything is valid.

The Formulas Behind the Calculator

Four formulas do all the work, and they are worth understanding. The maximum bending moment is M = P × L, the load times the length, acting at the fixed wall. For stress calculations the moment is converted to pound-inches by multiplying by 12. The maximum deflection at the free end is δ = P × L³ ÷ (3 × E × I), where L must be in inches and I is the moment of inertia — note the cubic dependence on length, which is why long cantilevers sag so dramatically. For a rectangular cross-section, the moment of inertia is I = b × d³ ÷ 12 and the section modulus is S = b × d² ÷ 6, where b is width and d is depth. Depth matters enormously: it is cubed in the inertia formula, so a deeper beam is vastly stiffer than a wider one. Finally, the maximum bending stress is σ = M ÷ S, in pounds per square inch. The shear force is simply V = P, the same everywhere along the beam.

Worked Examples

Example 1: a wooden diving-board-style beam, 6 feet long, carrying 500 pounds at the end, with a 3.5 by 7.25 inch cross-section and E = 1,900,000 psi. The moment is M = 500 × 6 = 3,000 lb-ft, which is 3,000 × 12 = 36,000 lb-in. The length in inches is 72. The moment of inertia is I = 3.5 × 7.25³ ÷ 12 = 3.5 × 381.078 ÷ 12 = 111.15 in⁴. The deflection is δ = 500 × 72³ ÷ (3 × 1,900,000 × 111.15) = 186,624,000 ÷ 633,555,000 ≈ 0.29 inches. The section modulus is S = 3.5 × 7.25² ÷ 6 = 30.66 in³, and the bending stress is σ = 36,000 ÷ 30.66 = 1,174.11 psi. The shear is 500 lbs. A deflection of about three-tenths of an inch and stress near 1,174 psi are both plausible for a stout timber beam.

Example 2: a 10-foot wooden shelf plank, 1.5 by 5.5 inches, with 200 pounds at the end. The moment is M = 200 × 10 = 2,000 lb-ft = 24,000 lb-in, and the length is 120 inches. The inertia is I = 1.5 × 5.5³ ÷ 12 = 1.5 × 166.375 ÷ 12 = 20.80 in⁴. The deflection is δ = 200 × 120³ ÷ (3 × 1,900,000 × 20.80) = 345,600,000 ÷ 118,560,000 ≈ 2.92 inches — the tip sags nearly three inches, which shows how punishing the length-cubed term is. The section modulus is S = 1.5 × 5.5² ÷ 6 = 7.56 in³, giving a stress of σ = 24,000 ÷ 7.56 = 3,173.55 psi, which exceeds what ordinary lumber should carry. This beam is undersized for the job, and the calculator’s numbers make that obvious.

Example 3: a short steel bracket, 4 feet long, 4 by 6 inches, carrying 2,000 pounds, with E = 29,000,000 psi. The moment is M = 2,000 × 4 = 8,000 lb-ft = 96,000 lb-in, and the length is 48 inches. The inertia is I = 4 × 6³ ÷ 12 = 72.00 in⁴. The deflection is δ = 2,000 × 48³ ÷ (3 × 29,000,000 × 72) = 221,184,000 ÷ 6,264,000,000 ≈ 0.04 inches — barely visible, thanks to steel’s stiffness and the short span. The section modulus is S = 4 × 6² ÷ 6 = 24.00 in³, and the stress is σ = 96,000 ÷ 24 = 4,000.00 psi, comfortably within steel’s capacity. The shear is 2,000 lbs.

How to Read Your Results

The result box lists six values. The maximum bending moment, shown in both pound-feet and pound-inches, is the demand at the wall — your connection and your beam must both handle it. The maximum deflection at the free end tells you how much the tip moves; compare it against serviceability limits, which are often expressed as fractions of the span like L/180 or L/240. The maximum bending stress is the number to compare against your material’s allowable stress: for example, structural lumber often allows roughly 1,000 psi in bending, so Example 2’s 3,173.55 psi is a clear failure while Example 1’s 1,174.11 psi is borderline. The shear force is constant along the beam and rarely governs for long beams but matters for short, deep ones. The moment of inertia and section modulus are the cross-section’s own properties — useful when comparing candidate sizes, since bigger I means less deflection and bigger S means less stress.

Common Mistakes to Avoid

The biggest mistake is mixing up units: length goes in feet, but width, depth, and the deflection formula’s length all work in inches — the calculator converts for you, but your inputs must be in the labeled units. A second mistake is using nominal lumber sizes (a “2×8”) instead of actual dimensions (1.5 × 7.25 inches), which inflates the computed strength. A third is forgetting that this covers a point load at the free end only; a load spread along the beam or placed mid-span needs different formulas. A fourth is ignoring the connection: the calculator sizes the beam, but the wall bracket or bolts must resist the same P × L moment. Finally, never treat these numbers as a stamped design — building codes, safety factors, dynamic loads, and connection details all sit outside this tool, so have a licensed engineer verify anything that holds weight over people.

Frequently Asked Questions

1. What is a cantilever beam?

A cantilever beam is fixed rigidly at one end and completely free at the other, like a diving board or a balcony. The fixed end, called the wall or support, must resist both the downward force and the rotating moment the load creates. Because there is no second support, the fixed end carries the entire structural demand alone.

2. Where do the maximum moment and deflection occur?

The maximum bending moment occurs at the fixed wall, where it equals P × L. The maximum deflection occurs at the free end, where the load is applied. This split is characteristic of cantilevers: the worst stress is at the support, but the worst movement is at the tip.

3. How is the deflection calculated?

With the formula δ = P × L³ ÷ (3 × E × I), where L is the length in inches, E is the material’s modulus of elasticity, and I is the moment of inertia. The length-cubed term dominates: doubling the length multiplies the deflection by eight, which is why short cantilevers feel rock solid and long ones feel springy.

4. Why is length in feet but width and depth in inches?

It matches how people actually talk about beams: spans are quoted in feet, while cross-sections are quoted in inches. The calculator converts the length to inches internally before applying the deflection and inertia formulas, so you just enter each number in its labeled unit and the math stays consistent.

5. What is E, the modulus of elasticity?

E measures a material’s stiffness — how much it resists stretching. Steel’s E of 29,000,000 psi is about fifteen times wood’s 1,900,000 psi, which is why the steel bracket in the examples deflects only 0.04 inches under a 2,000-pound load. Choose the dropdown option closest to your actual material.

6. What is the moment of inertia?

The moment of inertia, I, is a geometric property of the cross-section that measures resistance to bending. For a rectangle it is b × d³ ÷ 12. Because depth is cubed, a beam twice as deep is eight times stiffer. It is the single most important shape factor in the deflection formula.

7. What is bending stress, and how do I know if mine is safe?

Bending stress is the intensity of the push-pull forces in the beam’s fibers, in psi. Compare it to your material’s allowable stress: structural lumber is often limited to around 1,000 psi, aluminum higher, steel far higher. Example 2’s 3,173.55 psi on a wood plank is unsafe; always apply a safety factor and check your local code.

8. What is the section modulus?

The section modulus, S = b × d² ÷ 6, links the bending moment to the bending stress through σ = M ÷ S. A larger S means the same moment produces less stress. When shopping for beam sizes, S tells you about strength while I tells you about stiffness — a good design needs enough of both.

9. What is the shear force, and does it matter?

The shear force is the vertical slicing force in the beam, equal to the full load P everywhere along a cantilever with an end load. For long, slender beams it rarely governs the design, but for short, deep beams shear can become the limiting factor, so it is reported for completeness.

10. Can I use this for a load spread along the beam?

No. This calculator covers a single point load at the free end only. A uniformly distributed load uses different formulas: the moment becomes w × L² ÷ 2 and the deflection becomes w × L⁴ ÷ (8 × E × I). A load at mid-span is different again. Use the tool only for the loading case it was built for.

11. Why is cantilever deflection so much larger than a simply supported beam’s?

Two reasons. First, the cantilever formula has a 3 in the denominator where a center-loaded simply supported beam has a 48, making the cantilever sixteen times more flexible for the same span and load. Second, nothing restrains the free end. This is why cantilevered balconies and canopies need such deep, stiff members.

12. Does the beam’s own weight count?

The calculator ignores self-weight and analyzes only the point load you enter. For heavy materials like steel or long timber spans, self-weight acts as a small distributed load and adds a little extra moment and deflection. For light loads on short beams it is negligible; for marginal designs, add it to your load or consult an engineer.

13. How do I choose between wood, aluminum, and steel?

Wood is cheap and easy to work but the least stiff and weakest. Aluminum resists corrosion and is light, suiting outdoor or marine brackets. Steel is by far the strongest and stiffest but heavy and needs corrosion protection. Run the same load through each material option and compare the stress and deflection to see the trade-offs directly.

14. What connection does a real cantilever need?

A true moment-resisting connection: through-bolts with steel plates, welded brackets, or deep embedment into concrete. The connection must resist the full P × L moment plus the shear. A beam just resting on a support or held by a couple of nails is not a cantilever, and the wall or bracket is often the hardest part of the design.

15. Can this replace a structural engineer’s calculations?

No. This is an educational and preliminary-design tool based on idealized beam theory. Real construction involves safety factors, load combinations, dynamic effects, connection design, and code requirements that no single calculator covers. Anything structural — especially anything overhead or supporting people — should be reviewed by a licensed engineer.

Final Thoughts

The cantilever is simple to draw and demanding to build: one fixed end must do the work of two supports, and the math shows no mercy to long spans or shallow sections. This Cantilever Beam Calculator gives you the essential numbers — moment, deflection, stress, shear, and section properties — for the classic free-end point load in seconds. Use it to compare sizes, test materials, and build intuition before you commit to a design. And when the beam holds something that matters, let a licensed engineer sign off on the final numbers.