Skip to content
Physics

Race Tech Spring Calculator

Spring Rate & Force Calculator

Convert suspension spring rates between race-shop units and see how much force a spring pushes back with at a given compression.

The number stamped on the spring or in your setup sheet.
How far the spring is compressed: sag, preload, or full stroke.

Built on Hooke’s law: force equals rate times compression (F = k × x).

Your spring, converted and loaded

Rate in lbs per inch
Rate in N per mm
Rate in kg per mm
Spring force at this compression

Riders and racers obsess over spring rate for good reason: the spring is the heart of every suspension setup. Too soft and the bike dives, wallows, and bottoms out over every bump; too stiff and it skates across the surface instead of tracking it. Getting the rate right is the first step, and no clicker or preload adjustment can fix a wrong spring.

Confusion usually starts with units. American shops and setup sheets talk in pounds per inch, European and Japanese technical documents use newtons per millimeter, and garage conversations everywhere use kilograms per millimeter. A 4.8 N/mm spring and a 27 lb/in spring are nearly the same thing — but only if you know how to convert between them.

The calculator above removes the guesswork. Enter your spring rate in any of the three common units, add the compression distance you care about — rider sag, preload, or full stroke — and it converts the rate into all three units and tells you exactly how much force the spring pushes back with, using the simple physics of Hooke's law.

What Spring Rate Actually Means

A spring rate describes stiffness: how much force it takes to compress the spring by one unit of distance. A 5.0 N/mm spring needs 5 newtons of force for every millimeter of compression, so 50 mm of compression produces 250 newtons of pushback.

Higher numbers mean a stiffer spring. Most coil springs are linear, so force grows in direct proportion to compression — squeeze twice as far and the spring pushes back twice as hard.

The Three Units Race Shops Use

Suspension people use three units depending on where they learned the trade. American race shops use pounds per inch (lb/in): the pounds of force needed to compress the spring one inch. European and Japanese documents use newtons per millimeter (N/mm). Garage talk everywhere uses kilograms per millimeter (kg/mm), technically kilogram-force per millimeter.

All three describe the same physical property, so conversion is exact. One pound per inch equals about 0.1751 N/mm, and one kilogram per millimeter equals 9.80665 N/mm — the pull of gravity on one kilogram of mass.

Hooke's Law: Force Equals Rate Times Compression

Everything the calculator does rests on one relationship, Hooke's law, written as a standalone formula:

F = k × x

Force equals the spring rate (k) multiplied by the compression distance (x), as long as the spring stays within its elastic range and is not coil-bound. Convert the rate to N/mm and the travel to millimeters, and one multiplication gives the force in newtons; divide by 4.44822 to see it in pounds of force.

Converting Pounds per Inch to Newtons per Millimeter

To convert lb/in to N/mm, multiply by 0.1751268. That factor comes straight from exact definitions: one pound-force is 4.44822 newtons and one inch is 25.4 millimeters, so 4.44822 ÷ 25.4 = 0.1751268.

A 450 lb/in fork spring becomes 78.8 N/mm. A 600 lb/in shock spring becomes 105.1 N/mm. The calculator performs this conversion instantly whenever you select pounds per inch as the input unit.

Converting Newtons per Millimeter to Kilograms per Millimeter

Kilograms per millimeter is the friendliest unit for garage math because one kilogram of mass weighs about 9.81 newtons. Divide N/mm by 9.80665 to get kg/mm.

A 5.2 N/mm spring is a 0.53 kg/mm spring. Suspension charts often list rates in kg/mm for exactly this reason: the numbers are small and easy to compare, like 0.44, 0.46, and 0.48 for fork springs.

Why Compression Distance Matters

Rate alone does not tell you what the spring does on the bike — you also need the compression distance. The same spring pushes with a modest force at sag and a huge force at full stroke, and that difference is the whole story of suspension behavior.

Enter sag for the force at ride height, preload for the force the spring carries before you sit on the bike, or full stroke for the force at bottoming. Each one answers a different setup question.

Spring Sag vs. Preload vs. Full Stroke

Sag is how far the suspension compresses under the rider's weight — typically 25–35 mm on a fork and 90–105 mm on a shock for dirt bikes. Preload is the initial compression dialed in with the adjuster or spacer, which sets where sag lands.

Full stroke is the maximum compression the suspension allows. Force at full stroke tells you what slams into the bump stop, and whether your spring is stiff enough to keep you off it.

Worked Example: Dirt Bike Fork Spring in lbs/in

The shop sheet lists a fork spring at 26 lb/in, and you want to check it against the 0.46 kg/mm stamping while computing force at 30 mm of rider sag. Enter 26 lb/in as the rate and 30 mm as the compression.

Step one: convert the rate. 26 × 0.1751268 = 4.553 N/mm. Step two: convert to kg/mm. 4.553 ÷ 9.80665 = 0.464 kg/mm, matching the stamped 0.46 within rounding.

Step three: force at sag. 4.553 N/mm × 30 mm = 136.6 N, which is 30.7 lbf. That is the spring's push at ride height on each fork leg.

Worked Example: Converting a European Shock Spring

A shock spring is stamped 55 N/mm and your tuner talks in lb/in, so you need the conversion. Enter 55 as the rate in N/mm with 100 mm of compression as a representative stroke.

Step one: 55 ÷ 0.1751268 = 314.1 lb/in. Step two: 55 ÷ 9.80665 = 5.61 kg/mm. Now you can discuss this spring with any tuner in any unit system.

Force check: 55 N/mm × 100 mm = 5,500 N, about 1,236 lbf of pushback. Heavy, but that is a shock spring doing its job under full load.

Worked Example: Force at Rider Sag

A street bike runs 0.90 kg/mm fork springs and you measure 35 mm of rider sag. Enter 0.90 kg/mm and 35 mm.

Step one: convert to N/mm. 0.90 × 9.80665 = 8.826 N/mm. Step two: force. 8.826 × 35 = 308.9 N, about 69.4 lbf per leg or 138.9 lbf across both legs.

That number should roughly match the front-end weight carried by the forks — a quick sanity check that your sag measurement is honest.

Worked Example: Bottoming Force at Full Stroke

A shock spring rated 95 lb/in sees 60 mm of actual spring stroke at full wheel travel. Enter 95 lb/in and 60 mm.

Step one: 95 × 0.1751268 = 16.64 N/mm. Step two: 16.64 × 60 = 998.2 N, about 224 lbf. That is the spring's contribution at bottoming, before the bump stop adds its own rising force.

If that number looks small next to your riding weight, the spring is too soft or needs more preload — either way, expect harsh bottoming on big hits.

Linear vs. Progressive Springs

Everything so far assumes a linear spring: a constant rate from the first millimeter to the last. Most race springs are linear because predictable force makes damping and setup math clean and repeatable.

Progressive springs get stiffer as they compress and are common on street bikes for a plush initial feel with a firm finish. For those, Hooke's law only holds within a small slice of travel, so treat the calculator's force as an estimate and trust the manufacturer's rate curve.

How Spring Rate Affects Handling

Softer springs let the wheel follow bumps and keep the tire loaded, which means grip — up to a point. Too soft and the chassis pitches under braking, drags hard parts in corners, and blows through travel on square-edged hits.

Stiffer springs hold the chassis up and resist bottoming but transmit more harshness and can skip across chop. The right rate is the softest one that still controls bottoming and chassis attitude for your weight and pace.

Common Mistakes When Reading Spring Specs

The classic error is mixing units: reading a 5.0 as kg/mm when it was actually N/mm means fitting a spring roughly twice as stiff as intended. Always check the unit printed next to the number, not just the number.

Another is comparing fork and shock rates directly. They live in different worlds because of linkage ratios and travel lengths, so compare fork springs only to fork springs and shock springs only to shock springs.

When to Re-Spring Your Suspension

If correct sag needs preload at either extreme of the adjuster — nearly zero or nearly maxed out — the rate is wrong for your weight. Springs are chosen for the rider, not for the bike.

A good rule: set sag with the preload adjuster in the middle third of its range. If you cannot get there, move one rate step, about 0.02 kg/mm on forks, and measure again.

Using This Calculator in the Paddock

Keep the rate from your setup sheet handy and punch in sag numbers as you measure them. The force readout tells you whether a preload change actually altered the spring's working load or just moved the ride height around.

It is also the fastest way to translate a tuner's advice across unit systems — no conversion tables, no phone calculator, no unit mistakes at the worst possible moment.

Frequently Asked Questions

1. What is a spring rate?

A spring rate is a measure of stiffness: the force required to compress a spring by one unit of distance. It is expressed in pounds per inch, newtons per millimeter, or kilograms per millimeter, and higher numbers mean a stiffer spring that pushes back harder for the same compression.

2. How do I convert lb/in to N/mm?

Multiply the lb/in value by 0.1751268. For example, a 450 lb/in spring equals 78.8 N/mm. This factor comes from the exact definitions of the pound-force and the inch, so the conversion is precise rather than approximate.

3. How do I convert N/mm to kg/mm?

Divide the N/mm value by 9.80665, which is the gravitational acceleration that converts newtons to kilogram-force. A 5.0 N/mm spring is therefore about 0.51 kg/mm, the unit most garage setup conversations use.

4. What is Hooke's law?

Hooke's law states that the force a spring exerts equals its rate multiplied by its compression distance, written as F = k × x. It holds for linear springs within their elastic range and is the basis for every force figure this calculator produces.

5. How much force does my spring make at sag?

Enter your spring rate and your measured sag distance into the calculator. It converts the rate to N/mm, multiplies by the sag in millimeters, and reports the force in both pounds-force and newtons — the spring's pushback at ride height.

6. What spring rate do I need for my weight?

Spring rate is chosen so that correct rider sag falls in the middle of the preload adjuster's range. Heavier riders need higher rates. Suspension tuners publish weight-to-rate charts, and this calculator helps you compare chart values across unit systems.

7. Are fork and shock spring rates comparable?

No. Fork springs and shock springs operate at different travels and, on the shock side, through linkage ratios that multiply force. A 0.46 kg/mm fork spring and a 5.5 kg/mm shock spring can both be correct for the same rider on the same bike.

8. What is the difference between linear and progressive springs?

A linear spring has one constant rate through its whole travel, giving predictable force. A progressive spring's rate rises as it compresses, feeling plush initially and firm near the end. Race setups favor linear springs for consistent, repeatable behavior.

9. Does preload change the spring rate?

No. Preload compresses the spring a set amount before riding begins, which changes ride height and where you sit in the travel, but the rate — force per unit of additional compression — stays exactly the same.

10. Why does my bike bottom out with the sag set right?

Correct sag with frequent bottoming usually means the spring is too soft for your speed or terrain, the compression damping is too light, or the bump stop is worn. Check the calculator's full-stroke force figure: if it is low relative to your weight, go up a rate.

11. Can I mix units when comparing springs?

Only after converting. A bare number like 5.0 is meaningless without its unit — 5.0 N/mm and 5.0 kg/mm differ by a factor of nearly ten. Convert everything to one unit before comparing, which is exactly what this calculator does.

12. What does coil bind mean?

Coil bind happens when a spring is compressed until its coils touch each other, at which point the rate effectively becomes infinite and force spikes. Hooke's law no longer applies there, so never use force figures computed beyond the spring's usable travel.

13. How accurate is this calculator?

The unit conversions use exact defined constants, so they are precise. Force figures are exact for linear springs within their elastic range. For progressive springs or springs near coil bind, treat the force as an estimate.

14. Do I need different springs for track and street?

Often yes. Track riding at higher speeds and lean angles usually calls for stiffer springs to control chassis movement, while street riding favors softer rates for comfort over rough pavement. Many riders keep two sets and swap them.

15. Where is the spring rate stamped?

Most quality springs have the rate printed, etched, or painted on the spring body or on one end coil, sometimes alongside the free length. If the marking is worn off, measure wire diameter, coil count, and mean diameter — or simply replace the spring.