Synology Storage Calculator
Plan a Synology storage pool expansion. Enter your current usable pool size, the drives you are adding, and your RAID type to see your new total usable capacity and how much space the expansion gains you.
The usable space your pool has today, shown in Storage Manager.
For an accurate plan, new drives should be the same size or larger than your existing drives.
Every Synology NAS owner eventually hits the same moment: the storage pool that felt huge on day one is suddenly 85 percent full, and it is time to add drives. The question that follows is never just “how many drives can I add” but “how much space will I actually get.” The Synology Storage Calculator above answers that second question. Enter your current usable pool size, the number of new drives you plan to add, their size, and your pool’s RAID type, and it shows your new total usable capacity plus exactly how much of the new hardware turns into real, usable space.
What Is a Synology Storage Pool Expansion?
A storage pool is the group of drives in your Synology NAS that work together as one big volume. When the pool fills up, you do not have to start over: Synology lets you expand the pool by inserting additional drives or replacing existing drives with bigger ones. This calculator focuses on the most common path, which is adding new drives to a pool that already exists. The important insight is that the raw size of the drives you add is never the amount of space you gain. A portion of every drive set is reserved for redundancy, which is the safety net that keeps your data alive if a drive fails. The RAID type of your pool decides how large that safety net is, and therefore how much of each new drive becomes usable storage. Adding two 12 TB drives does not automatically give you 24 TB of new space, and guessing wrong is how people buy the wrong number of drives.
How to Use the Synology Storage Calculator
Start with your current usable pool capacity in terabytes, which you can find in the Synology Storage Manager; this is the space available today, not the raw size of the drives already installed. Next, enter the number of new drives you plan to add as a whole number, then the size of each new drive in terabytes. Ideally the new drives are the same size as, or larger than, the drives already in the pool, because expansion math is cleanest that way. Finally, choose the RAID type of your existing pool from the dropdown: SHR or RAID 5 for one-drive redundancy, RAID 6 for two-drive redundancy, RAID 10 for mirrored pairs, or Basic or JBOD if you use no redundancy. Press Calculate and the tool shows your new total usable capacity in large type, with a breakdown of your current pool, the drives you are adding, the RAID type, and the expansion gain, which is the new usable space the added drives actually produce.
The Expansion Math Explained
The math is simple once you see what redundancy costs. Think of each RAID level as a rule about how many drives’ worth of space is set aside for protection. In SHR, which is Synology’s flexible RAID, and in classic RAID 5, one drive’s worth of space is reserved for parity, the recovery information that lets the pool rebuild after a failure. So the usable space gained from adding new drives is (number of new drives minus 1) multiplied by the drive size. Add two 12 TB drives to an SHR pool and you gain (2 − 1) × 12 = 12 TB of usable space, not 24. In RAID 6, two drives’ worth of space is reserved for parity, so the gain is (number of new drives minus 2) multiplied by the drive size; adding four 16 TB drives gains (4 − 2) × 16 = 32 TB. RAID 10 works in mirrored pairs, so only half of each pair is new usable space: the gain is (number of new drives divided by 2) multiplied by the drive size, which means six 20 TB drives gain 60 TB. In Basic or JBOD mode there is no redundancy at all, so every terabyte counts: the gain is simply the number of new drives multiplied by the drive size. Your new total is then your current usable pool plus this gain.
One nuance worth understanding is why SHR and RAID 5 treat expansion the same way. SHR is Synology’s friendlier version of RAID 5: it handles mixed drive sizes more gracefully when the pool was created, but once the pool exists, adding drives follows the same one-drive-redundancy rule. That is why the calculator groups them together. Another nuance is that Synology counts in decimal terabytes for display, so the calculator shows results in decimal TB with two decimals. The file system itself also holds back a small reservation, which is why the tool notes its figures are planning estimates rather than the exact number Storage Manager will show down to the gigabyte.
Worked Examples
Example one. A home user has a current usable pool of 10.90 TB and adds two new 12 TB drives to an SHR pool. Step one, the redundancy rule for SHR is one drive’s worth of parity, so the expansion gain is (2 − 1) × 12 = 12.00 TB. Step two, the new total is the current 10.90 TB plus the gain of 12.00 TB, which equals 22.90 TB. This is the classic surprise for first-time expanders: two 12 TB drives in the box turned into 12 TB of usable space, and the calculator shows exactly why.
Example two. A small business has 20.00 TB usable and adds four new 16 TB drives to a RAID 6 pool for extra safety. Step one, RAID 6 reserves two drives’ worth of parity, so the gain is (4 − 2) × 16 = 32.00 TB. Step two, the new total is 20.00 + 32.00 = 52.00 TB. The business traded some capacity for the comfort of surviving two simultaneous drive failures, and the math makes the cost of that comfort visible.
Example three. A video editor has 30.00 TB usable and adds six new 20 TB drives to a RAID 10 pool for maximum speed. Step one, RAID 10 mirrors everything, so the gain is (6 ÷ 2) × 20 = 60.00 TB. Step two, the new total is 30.00 + 60.00 = 90.00 TB. Note that six is an even number, which RAID 10 requires; trying to add an odd number of drives would fail, and the calculator flags that as an error rather than producing a misleading number.
How to Interpret Your Result
The headline number is your new total usable capacity in terabytes: the current pool plus the expansion gain. This is the number to compare against how much data you expect to store over the next year or two. The breakdown rows tell the story behind it. The expansion gain row is the most important for planning, because it is the actual return on the money you spend on new drives. If the gain looks smaller than you hoped, you have three honest options: add more drives, buy bigger drives, or, only if you truly understand the risk, reconsider whether your current RAID level is right for your needs. A useful habit is to plan expansions before the pool passes 80 percent full, since rebuilding and expanding take time and a nearly full pool leaves little room to maneuver.
Choosing Drives for Your Expansion
The calculator assumes each new drive is the same size, and that is the cleanest way to expand. Synology officially supports adding drives that are equal to or larger than the smallest drive already in the pool, but if you mix sizes, only part of a bigger drive may be usable in the pool, and the extra space sits idle until all drives are upgraded. This is the single biggest source of “missing” terabytes after an expansion. NAS-rated drives are also worth the small premium over desktop drives: they are built for 24-hour operation, vibration tolerance in multi-bay enclosures, and the long rebuild times that expansion triggers. Finally, add all your new drives in one expansion when you can, rather than one at a time, because each expansion cycle stresses the existing drives with a full rebuild, and fewer cycles mean less wear.
Common Mistakes to Avoid
The most common mistake is counting raw drive capacity as usable space and buying fewer drives than the plan needs; the parity row in the breakdown exists precisely to make that cost visible. The second mistake is adding a single drive to a RAID 6 pool and expecting the calculator to approve it: RAID 6 cannot maintain two-drive redundancy with only one new drive, so plan for at least two. The third mistake is adding an odd number of drives to a RAID 10 pool, which mirroring does not allow. The fourth mistake is mixing in a smaller drive than the pool already has, which Synology will reject and which wastes the purchase. The fifth mistake is expanding a pool that is already 95 percent full and expecting smooth sailing; leave headroom, because Btrfs snapshots and rebuilds need breathing room. And remember this is a planning estimate: always confirm the final number in Storage Manager after the expansion completes.
Frequently Asked Questions
1. What is a Synology storage pool?
A storage pool is a group of drives in your Synology NAS that are combined into one large volume. Your shared folders live on top of it, and expanding the pool is how you add more space without starting over.
2. Does adding drives erase my data?
No. Expanding a pool by adding drives keeps your existing data intact. The NAS redistributes parity across the new drives in the background. You should still keep a backup, because any drive operation carries some risk, but expansion itself does not format anything.
3. Why is the expansion gain less than the drives I added?
Because part of the new capacity is reserved for redundancy. SHR and RAID 5 reserve one drive’s worth of space for parity, RAID 6 reserves two, and RAID 10 mirrors half of everything. The calculator’s gain row shows exactly how much remains usable.
4. What is SHR on a Synology NAS?
SHR, or Synology Hybrid RAID, is Synology’s automated RAID system. For pools built with same-size drives it behaves like RAID 5 with one-drive redundancy, and it is more forgiving when you later replace drives with bigger ones.
5. Can I add just one drive to expand?
Yes for SHR, RAID 5, and Basic pools: the calculator allows one drive and shows the gain. RAID 6 needs at least two new drives and RAID 10 needs an even number, so the calculator will warn you if the count does not fit the RAID rules.
6. Do the new drives need to match my existing drives?
They should be the same size or larger than the smallest drive already in the pool. Matching sizes is cleanest; a larger drive may leave some of its space unused until the rest of the pool catches up.
7. RAID 5 or RAID 6 for a home NAS?
RAID 5 or SHR is fine for most home pools with a backup, since it costs only one drive’s worth of space. RAID 6 costs two drives’ worth but survives two simultaneous failures, which suits larger pools where rebuilds take days.
8. How long does an expansion take?
Hours to days, depending on drive size, drive count, and how busy the NAS is. The pool stays usable during the process, but performance is reduced, so start expansions when you do not need full speed.
9. What does the file system reserve?
Btrfs and ext4 both hold back a small percentage for metadata and system use, so Storage Manager may show slightly less than the calculator’s estimate. The difference is small, typically a few percent, and the calculator’s note mentions it.
10. Can I expand with a bigger drive than my existing ones?
Yes. In an SHR pool, replacing or adding larger drives works, but the extra space above the smallest drive size only becomes usable once enough drives are upgraded. Adding drives of mixed sizes is the most common cause of confusing results.
11. What is the difference between a pool and a volume?
The pool is the raw combined capacity of the drives; the volume is the formatted space carved out of the pool where your files live. You expand the pool first, and then you can expand the volume into the new space.
12. Does RAID 10 really halve my new drives?
Yes. RAID 10 mirrors every drive, so each pair of new drives adds only one drive’s worth of usable space. You get excellent speed and can survive certain multi-drive failures, but you pay for it in capacity, exactly as the calculator shows.
13. When should I expand my pool?
Around 70 to 80 percent full is the sweet spot. Waiting until 95 percent or more leaves no room for snapshots or rebuilds to work comfortably and turns a routine expansion into a stressful one.
14. Can this calculator plan drive replacement instead of adding drives?
Not directly. This calculator plans adding new drives to an existing pool. Replacing drives with bigger ones one at a time follows different rules, especially under SHR, and is best planned with Synology’s own RAID calculator.
15. Is the result exact?
It is a planning estimate. Drive overhead and the file system’s own reservations mean Storage Manager may show a slightly different final number. Use the result to decide how many drives to buy, then confirm in Storage Manager after expanding.
Final Thoughts
Expanding a Synology pool is one of the safest upgrades you can make to a NAS, as long as you know what the new drives will actually give you. The Synology Storage Calculator turns the RAID overhead rules into a single clear number: your new total usable capacity and the real gain from the drives you are about to buy. Plan before the pool fills up, match your drive sizes, add drives in one go when you can, and always keep a backup. Do that, and the moment your NAS warns you about space will become a ten-minute shopping decision instead of a weekend of regret.