Bending Moment Diagram Calculator
Key shear and moment values for plotting your diagram (estimate).
Simply supported beam, static loads. Values are estimates — verify critical designs with a licensed engineer.
Engineers rarely design a beam from a single number. They draw two pictures: the shear force diagram, which shows how the vertical forces shift along the beam, and the bending moment diagram, which shows where the beam bends the hardest. Those diagrams reveal the critical points — the largest shear, the largest moment, and exactly where they occur — and everything downstream (choosing a section, checking stress, detailing connections) flows from them. The Bending Moment Diagram Calculator above gives you every key value you need to sketch both diagrams accurately: the support reactions, the shear just inside each support and on both sides of the point load, and the maximum bending moment with its precise location.
You do not need to be an engineer to use it. Enter the span, one point load with its position, and one uniform distributed load with its start and length — the two load types that cover the vast majority of real beams — and press Calculate. The result is the complete set of ordinates for your diagrams: plot the shear values at their stations and join them with straight lines (dropping vertically at the point load), then plot the moment values — zero at both supports, peaking at the reported maximum — and join them with straight segments under point loads and gentle curves under the distributed load. What used to be a page of statics homework becomes a ten-second step.
What the Bending Moment Diagram Calculator Does
This calculator computes the defining numbers of the shear and bending moment diagrams for a simply supported beam carrying one point load and one uniform distributed load. It starts with static equilibrium to find the reactions R1 and R2. From there it evaluates the shear force at the critical stations: just right of the left support, just left and just right of the point load (shear jumps down by the load’s weight at that point), and just left of the right support. Finally, it locates the maximum bending moment by checking every station where the peak can occur — the supports, the point load position, the ends of the distributed load, and any point inside the distributed load where the shear crosses zero (the moment peaks exactly where shear is zero).
The output is diagram data, not the drawing itself: the numbers you would plot, with the maximum moment and its distance from the left support called out explicitly. The model assumes vertical static loads on simple supports at both ends. Within those assumptions the values follow directly from equilibrium, so the numbers are exact for the inputs you give — the “estimate” label reflects the simplified model, not the arithmetic.
How to Use the Bending Moment Diagram Calculator
Enter the span in feet first. Then the point load: its weight in pounds and its distance in feet from the left support (leave both blank for no point load). Then the uniform distributed load: intensity in pounds per foot, where it starts in feet from the left support, and the length it covers (leave all three blank for no distributed load). For a distributed load over the whole beam, start at 0 and set the length equal to the span. At least one of the two load types must be present.
Press Calculate to receive the reactions, the four key shear values, and the maximum bending moment with its location. Validation guards the physics: span must be positive, the point load position must lie on the beam, no value may be negative, a distributed intensity needs a positive length, and the distributed stretch must fit inside the span — any violation produces a red message naming the problem. Reset clears the form.
The Formula Behind the Calculator
Everything starts with the reactions. Collapsing the distributed load to its resultant W = w × lu acting at xw = s + lu ÷ 2, moment equilibrium about the left support gives R2 = (P × a + W × xw) ÷ L, and force equilibrium gives R1 = P + W − R2. These two numbers anchor both diagrams: shear starts at +R1 at the left support and ends at −R2 at the right.
The shear at any position x is the running balance of vertical forces to the left of x: V(x) = R1 − (distributed weight left of x) − P (if x is past the point load). The distributed weight left of x is w times the overlapped length, which is zero before the load starts, grows linearly through it, and stays constant after it ends. Evaluating this at the stations gives the four reported shear values, and the sudden drop of P between “just left” and “just right” of the point load is the unmistakable signature of a concentrated load on a shear diagram.
The bending moment at x accumulates those shears: M(x) = R1 × x − (distributed weight left of x) × (x − its centroid) − P × (x − a) for x past the load. The maximum must occur either at a station where the loading changes character — the supports, the point load, the ends of the distributed load — or where the shear crosses zero inside the distributed region, since a zero slope marks the peak of the moment curve. The calculator solves for those zero-shear points exactly (x = s + R1 ÷ w before the point load, x = s + (R1 − P) ÷ w after it) and reports the largest moment found, with its location measured from the left support.
Worked Examples
Example 1 — center point load plus full-span uniform load. L = 10 ft, P = 1000 lbs at a = 5 ft, w = 200 lbs/ft from s = 0 over lu = 10 ft. Resultant: W = 200 × 10 = 2000 lbs at 5 ft. Total = 3000 lbs. R2 = (1000 × 5 + 2000 × 5) ÷ 10 = 15000 ÷ 10 = 1500.00 lbs; R1 = 3000 − 1500 = 1500.00 lbs. Shear: just right of left support 1500.00 lbs; just left of the point load 1500 − 200 × 5 = 500.00 lbs; just right 500 − 1000 = −500.00 lbs; just left of right support 1500 − 2000 − 1000 = −1500.00 lbs. Moment candidates: the point load station gives M = 1500 × 5 − 1000 × 2.5 = 7500 − 2500 = 5000.00 ft-lb, the largest found — so the maximum bending moment is 5000.00 ft-lb at 5.00 ft from the left support, right under the point load.
Example 2 — off-center point load, no distributed load. L = 12 ft, P = 1200 lbs at a = 4 ft, distributed boxes blank. R2 = 1200 × 4 ÷ 12 = 400.00 lbs; R1 = 1200 − 400 = 800.00 lbs. Shear: 800.00 just right of the left support, still 800.00 just left of the load (nothing distributed to erode it), then 800 − 1200 = −400.00 just right of the load, and −400.00 at the right support. Moment under the load: M = 800 × 4 = 3200.00 ft-lb, the peak — maximum bending moment 3200.00 ft-lb at 4.00 ft from the left. Notice the classic pattern: constant shear between loads, a vertical drop at the point load, and a triangular moment diagram peaking under it.
Example 3 — the peak hides inside the distributed load. L = 10 ft, P = 600 lbs at a = 2 ft, w = 150 lbs/ft from s = 4 ft over lu = 4 ft. Resultant: W = 600 lbs at 6 ft. R2 = (600 × 2 + 600 × 6) ÷ 10 = 4800 ÷ 10 = 480.00 lbs; R1 = 1200 − 480 = 720.00 lbs. Shear: 720.00 at the left, 720.00 just left of the point load, 120.00 just right of it, then falling through the distributed stretch to −480.00 at the right support. Shear crosses zero inside the distributed load at x = 4 + (720 − 600) ÷ 150 = 4.80 ft. Moment there: 720 × 4.8 − 120 × 0.4 − 600 × 2.8 = 3456 − 48 − 1680 = 1728.00 ft-lb — larger than the 1440.00 ft-lb under the point load. Maximum bending moment: 1728.00 ft-lb at 4.80 ft from the left. This is the case that rewards doing the math: the worst moment is not under the point load at all.
Understanding Your Results
Read the results as a tour along the beam from left to right. The shear starts at +R1, stays flat where there is no distributed load, slopes downward through the distributed region, drops vertically by P at the point load, and arrives at −R2 at the far support. If your numbers do not do exactly this — if the last shear is not the negative of R2, for instance — recheck the inputs, because equilibrium is non-negotiable.
The moment starts at zero at the left support (simple supports carry no moment), rises to its maximum, and falls back to zero at the right support. The reported location tells you where the beam works hardest — that is where bending stress peaks, where a splice must never go, and where reinforcement or a deeper section matters most. A maximum under the point load is the ordinary case; a maximum inside the distributed region, as in Example 3, is the interesting one, and it is precisely why the calculator hunts for zero-shear points instead of only checking the obvious stations. Sketch the values on paper once, and the two diagrams will feel less like abstract theory and more like a map of your beam.
Common Mistakes to Avoid
The most common mistake is assuming the maximum moment is always under the point load. Example 3 proves otherwise: with a distributed load nearby, the peak can sit where the shear crosses zero inside the distributed stretch. Always read the reported location rather than assuming it. Second, people plot the shear diagram but forget the vertical drop at the point load — shear does not glide through a concentrated load, it steps down by the full weight instantly.
Third, mixing up the sign convention. In this calculator, upward forces on the left are positive shear, and sagging (concave-up) moment is positive — the standard convention in most textbooks. If your course or software uses the opposite signs, flip them consistently rather than mixing. Fourth, entering the distributed load’s start and length so that it overhangs the support: the stretch must fit within the span, and the tool rejects anything that does not. Fifth, forgetting that blanks mean zero — a forgotten point load position defaults to 0, the left support, which silently changes the answer. Finally, remember these are static values; impact, vibration, and moving loads need additional factors before they govern a design.
Frequently Asked Questions
1. What is a bending moment diagram?
It is a plot of the internal bending moment at every point along the beam. It starts and ends at zero at simple supports and peaks where the beam bends most — the values this calculator reports are exactly the points you would plot.
2. What is a shear force diagram?
The companion plot: vertical internal force at every point along the beam. It starts at +R1, changes wherever loads act, and ends at −R2. The four shear values from the calculator are its key ordinates.
3. Why does shear drop suddenly at the point load?
Because a concentrated load is, mathematically, an instantaneous addition of downward force. The running balance of vertical forces steps down by the full load weight at that exact point — the vertical cliff on the diagram.
4. Why is the maximum moment where shear equals zero?
The slope of the moment diagram equals the shear. Where the slope is zero, the curve has a peak (or valley) — so the maximum moment sits exactly at the zero-shear point. This is the fundamental link between the two diagrams.
5. Can the maximum moment be somewhere other than under the point load?
Yes. When a distributed load is present, shear can cross zero inside the distributed region, and the moment peaks there instead. Example 3 in this article shows a real case: the peak sits at 4.80 ft while the point load is at 2 ft.
6. Why is the moment zero at the supports?
Simple supports can push up or down but cannot resist rotation, so they cannot develop a moment. The moment diagram therefore always starts and ends at zero — a built-in check on any diagram you sketch.
7. What are the units of the results?
Reactions and shears are in pounds; the bending moment is in foot-pounds; the location is in feet from the left support. All distances were entered in feet, so everything stays consistent.
8. How do I sketch the diagrams from these numbers?
Plot the shear values at their stations on a horizontal axis, join with straight lines, and drop vertically by P at the point load. For moment, mark zero at both supports and the maximum at its location, joining with straight segments under point loads and smooth curves under distributed load.
9. What if I have no distributed load?
Leave its three boxes blank. The shear stays constant between the supports except for the drop at the point load, and the moment diagram is two straight lines peaking under the load — the classic textbook case.
10. What if I have no point load?
Leave its boxes blank and enter only the distributed load. The shear then slopes linearly through the loaded region, and the maximum moment sits where that sloping shear crosses zero.
11. Why does the calculator check so many candidate points?
The moment peak can only occur where the loading changes character or where shear is zero. Checking all candidates — supports, load points, distributed-load ends, and zero-shear points — guarantees the true maximum is found, including sneaky cases like Example 3.
12. Do negative shear values mean something is wrong?
No — negative shear on the right half of the beam is completely normal. It simply means the net vertical force to the left of that section points downward. Shear must finish at −R2 at the right support.
13. Can I use this for a beam with supports that are not at the ends?
No. This tool models supports exactly at the two ends of the span. Overhangs beyond the supports change the diagrams (and can create negative moments), which needs a more general analysis.
14. How is this different from a beam strength calculator?
This tool maps where the beam works hardest — the diagram data. A strength calculator takes the resulting maximum moment and checks it against what the cross-section can take. Use this one to find the demand, then the strength check to verify capacity.
15. Is this enough to design a real beam?
It is the correct first half: accurate demands from a clear model. The second half — allowable stresses, deflection limits, lateral stability, connections, and code provisions — still belongs to a licensed engineer on any real structure.
Final Thoughts
The Bending Moment Diagram Calculator hands you the skeleton of both diagrams — reactions, key shears, and the maximum moment with its address on the beam — in the time it takes to type six numbers. Plot those points, join them with the right shapes, and you are looking at the same picture a structural engineer starts from. The numbers are simple; knowing where the beam works hardest is what makes them powerful.